Software
Houzz Logo Print
hzdeleted_35844888

Any use for pine bark siftings?

7 years ago

After screening coarse pine bark mulch through 1/2" screen to get the really big particles out, I noticed very fine, dusty particles at the bottom. So I ran it through a little smaller than 1/8" screen so my 5-1-1 mix would have nothing smaller than that in the mix.

What I ended up with was a pail of leftovers, with dust sized particles to almost 1/8" pieces of bark. There's also tiny bits of wood or sap wood in this.


What would be the best use for something like this?


Is there an easy way to get the wood chips out?

I'll be starting conifer seeds later this spring, would it make good seed starter?

Or should I just throw it into the garden to increase the OM content?



Comments (15)

  • 7 years ago

    why did you feel this was needed ... did you use a mask??


    i would probably just throw it out the back door.. on top of the snow ... if i had extra space in the incubator .. i might try one pot with just that in it.. just to see what happens ...


    if you wet it.. and then allow it to redry .. you might have a hard time rewetting it again ... aka drainage/wetting issues ...


    ken

    User thanked ken_adrian Adrian MI cold Z5
  • 7 years ago

    I just didn't think using the dust fine bottom screenings was a good idea, I thought it might plug up the 5-1-1.

    I put it through the 1/8" screen again and a lot of the sap wood and toothpicks stayed in the screen this time. Maybe because it was drier? It's about the consistency ranging from ground coffee down to like talcum powder. Yes, I keep a few dust masks around for bark and perlite screening.

    No snow here.

    I have plenty of seeds, so maybe I'll try it for germination or try a pot once rootings are ready to pot up. I only have a few quarts of it so it won't last long. Thanks!


  • 7 years ago

    I wouldn't use it for seed starting. Likely too acidic if not yet treated with lime. Is it composted bark fines? If not, there might also be issues with N unavailability. Potting up seedlings (or as a media for cuttings) should be OK

    And you can always add it to the 5-1-1 in place of some or most of the peat, if you like.

    User thanked gardengal48 (PNW Z8/9)
  • 7 years ago

    I'm sure there is still a fair amount of wood particles in it.

    What problems does the wood bring? Mold?

  • 7 years ago

    i would think there might be long term watering/drainage issues .... with straight fines ... either too wet.. or too dry ... and once dry.. getting water to flow thru it properly ....


    and then with too much dampness comes the mold/algae potential ...


    as gal notes.. there could be long term nutrition availability ... but that might depend on how long you plan on leaving them in said product.. rather than potting them up when they get to size .... which in tree time might be late spring or so .... you can probably provide whatever they might need.. with diluted water sol fert ...


    keep in mind.. when potting up couple inch babes.... multiples can go into a bigger pot... with appropriate media ... which would no longer be a seedling mix ...


    ken



    User thanked ken_adrian Adrian MI cold Z5
  • 7 years ago

    okay, thanks,

    I think I understand it better now.

    When I read about this stuff, it says to pick out the little wood toothpicks and pieces. I suppose considering bark is a 'soil-less' media, the wood would break down into 'soil'? Shortening the life if used as a container mix? It probably doesn't matter with short term usage like I use it for but Inquiring minds want to know. :-)

  • 7 years ago

    I chuck it below my azaleas or other acid loving plants.


    User thanked mblan13
  • 7 years ago

    No wonder why blueberries grow so good in the pine woods north of me. :-)

  • 7 years ago

    I don't generally screen my bark for the 5:1:1 mix. I sort of judge the volume of really fine material (everything smaller than 1/10 of an inch) it contains before I add an appropriate amount of peat to give me the water retention I prefer, which is always on the sparse side because I prefer soils that need watering every day in the summer because the added air porosity promotes excellent root health. What you did by removing all the fines was increase the amount of peat you'll need to bring the water retention up to what you prefer. It's not a sin - just a step that wasn't really necessary.

    You can't get all of the sapwood out of the bark, so no need to be too particular about it. You don't want your bark to be much more than 5% sapwood though. Sapwood increases the o/a decomposition rate of the soil, so increases the heat generated by decomposition, which can be very significant when pine sapwood or hardwoods constitute a significant % of the medium. There is also an upward pH spike associated with the use/decomposition of sapwood and particularly hardwoods.

    You can mix it back into the soil, or top-dress any beds, raised beds, or gardens you might have.

    Al

    User thanked tapla (mid-Michigan, USDA z5b-6a)
  • 7 years ago

    Hi Al!

    Most of the sapwood was stringy, in lengths, so much of it stayed in the screen and what didn't was easily picked out, so I think I'm good with that part.

    Considering the amount of bark I started with, these fines are only a small percentage, so I can see now that I could've just left it in there. Live and learn. :-)

    Thanks for the information.

    I used some of the 511 I mixed up last summer to pot up some seedling Honey locust that I started from seed and man did they do good! I'm having more success since I discovered your recipe.

    I had to replace a hanging Calibrachoa I bought that had failed in the standard peat potting mix that came with the hanging plants. We had a rainy spell early and I think it just couldn't take the moisture. I replaced the peat soil in the pot with 511 and bought a new one in a small container, for $1.00. By the end of summer it was an impressive looking plant. I watered it daily and it grew like crazy!

    So thanks for inventing this stuff :-)

  • User thanked Nil13 usda:10a sunset:21 LA,CA (Mount Wash.)
  • 7 years ago

    I ended up making a 5-2-0 mix with the bark fines, no peat and 2 parts perlite.

    And of coarse Dolomite lime. Hoping it works for initial potting of some Picea abies seeds that I'm germinating. Should drain good. I may be short on potting media this year so thinking this will help. It's doing me no good sitting on the shelf. :-)


  • 7 years ago
    last modified: 7 years ago

    It probably won't drain well. It won't drain just because its pine bark. If the bulk of the mix is below 1/10 of an inch it will not drain well due to adhesion/cohesion properties of water.

    User thanked mblan13
  • 7 years ago
    last modified: 7 years ago

    So, should I up the perlite?

    Or better to add some coarse bark 511 to it?

    It's going to be used in very small starter pots, 1-1/2" dia. x 2" deep, immediately after the seed germinates, then up potted in a few weeks.