Software
Houzz Logo Print
colorado_plantswoman

Advice for repointing glass block window

7 years ago

Hello.

I have a glass block window that needs repointing. Because of the housing boom in Fort Collins, CO, it's impossible to find a tuckpointer who's available, so I may have to do the work myself. I've done some brick tuckpointing before, but never on a glass block window. Are there any tips you can offer for cleaning out the existing mortar and repointing a glass block window successfully?



Comments (12)

  • PRO
    7 years ago

    How much do you really need to clean out? They tend to stay pretty tight and just break down on the top level of the mortar where they can be just lightly scratched out with a grout scraper and then topped off.

  • 7 years ago

    They need deep cleaning. When I cleaned the mortar out of a vertical crack at the top, I discovered that the mortar is gone almost all the way through to the interior of the house. On the sides, the original homeowner filled in the gaps along the sides of the window with caulk instead of replacing the mortar.

  • PRO
    7 years ago

    An oscillating tool with a grout blade would work nice.

  • PRO
    7 years ago

    If they are deeper, plan on investing in the tool that Todd references above. They are handy little buggers and you will find something else to use them for in the future. Just make sure you don't go all the way through or you will loosen the blocks.

  • 7 years ago

    Thanks, guys! I've been looking for an excuse to buy an oscillating tool for years. Now I finally have one.

  • 7 years ago

    I have been in the same situation of looking for an excuse for years. And I never quite had a job that was big enough to justify spending several $100s. I then saw an oscillating tool at Costco for about $50 and bought it on a whim. I am sure it is lower quality than the fancy tools that I had previously been drooling about. But on the other hand, I have already gotten more than $50 worth of use out of it in just a few months. It's funny how when you have the right tool, there all of a sudden are lots more projects that you can tackle successfully.


    So, hypothetically, if it broke at this point, I wouldn't fret too much. And then, I'd go out and buy one of the fancy ones. In hindsight, should have done that years ago anyway. It's a great little tool that every homeowner should have. Having said that, so far the Costco tool is going strong and shows no significant signs of wear or tear.

    Deb thanked M
  • 7 years ago

    When I was researching tuckpointing years ago, I read that you should slightly moisten surrounding mortar to help new mortar adhere to it. Is that true?

  • PRO
    7 years ago

    Yes. Keeps it from curing too fast.


    A spritz with a water bottle spray is all you need.

    Deb thanked Windows on Washington Ltd
  • 5 years ago
    last modified: 5 years ago

    i have a garage full of tools, (mostly) corded and not. rechargeables have their limited place, expensive and prone to whatever the mfr decides to expire them via battery confirguration. I have corded craftsman drills, reciprocating saws, etc from 50 years ago that work just like the day i bought them, can you say the same for rechargeables from 5 years ago!

    Corded provide sustainable reliable power!

  • 5 years ago

    Seems like everyone is approaching this as though tuckpointing a glass window is the same as tuckpointing brick. I don't think so. Brick is porous and mortar can bond to it. And the spritz of water is to wet the pores so the mortar cures and doesn't dry out. Glass is non-porous and does mortar even bond to it? I would think OSI Quad caulk would be more appropriate to reseal it.


    Personally, glass windows have an R-value of about 2, so I would be looking to replace it with a real window instead.

  • PRO
    5 years ago

    It is actually alot like tuckpointing with easier clean up. The grout is specific to glass block and bonds well. Quad would be a horrible choice .