Software
Houzz Logo Print
jonathan_gunnell

Leaky Tub Spout

4 years ago
last modified: 4 years ago

I'm wrapping up a full bathroom renovation and down to the trim and caulking. I can't get this tub spout to stop leaking. It is not leaking from the threaded 1/2" nipple on either end. It looks like it's actually leaking from the internal diverter assembly. I can't find any good images of the internal parts to share and I'd rather not take it off again until I have a plan to fix it because it took me forever to get it tight to the wall and facing the right direction.

Any ideas on how to fix it? Should I contact Delta for a replacement? Should I just make sure I caulk really well and ignore it?




Here was the rough in before it was closed up. It's copper up to the shower head as well.


Comments (9)

  • 4 years ago
    last modified: 4 years ago

    Update. Delta customer service didn't sound confident about what the issue was, but they're sending a new cartridge for the valve. I have a feeling that's not going to resolve the issue, but I'll provide an update here when that comes in if there are responses.

  • 4 years ago

    That wouldn't be from the mixing valve, although it could be at the nipple-to-spout connection outside the wall. Your diverter tub spout should have 2 or 3 connections inside of it that you have to adjust so it fits tight against the wall. I suspect you haven't put enough teflon tape on the threads of these.

  • 4 years ago

    I agree. I have no idea why they insisted on sending me a new cartridge for the valve when the issue is obviously the spout. There is plenty of tape on both ends of the threaded nipple and it is super secure in both ends. No water is ending up behind the wall at all, just leaking out of the bottom end of the spout itself right against the wall. It's almost like the water pressure is too high and the spout isn't able to handle it, so it's forcing the water back out of the diverter assembly pieces.

  • 4 years ago
    last modified: 4 years ago

    I'm not talking about the ~6" nipple from the drop ear elbow in the wall. I'm talking about the multiple parts inside the spout that you adjust in or out to allow the spout to flush against the wall. Those all need tape too (or dope sometimes when plastic threads have too much play). There's probably 1 or 2 threads and maybe 1 or 2 gasketed pieces. Whatever it is, you can't let it continue or it will be behind your wall soon enough.

  • 4 years ago

    Right. That's the diverter assembly I mentioned in my original post. There are no adjustments that can be made to change how flush it is against the wall with this model. There is one thin piece with an o ring that screws into the spout and it is flush with the edge of the spout. That piece essentially just holds the nipple in place and against the stopper. Again, I wish I could find pictures of the inside assembly but apparently, that's the only thing that doesn't exist on the internet.


    I lubricated the o ring before installing as recommended in the instructions. The metal piece screws into the plastic housing inside the spout. Since it's plastic, I was under the impression that tape and/or pipe dope shouldn't be used. Am I wrong about that?


    Behind that is the stopper attached to the diverter bar. All of those pieces are intact and in place. I'm not too worried about water getting behind the wall because it is only dripping from the bottom of the spout, well below the nipple, and the nipple itself is sealed well with a Kerdi pipe seal. I have easy access behind the wall in that section so I've been keeping my eye on it. The water that drips below the spout eventually finds its way to the tub with the exception of a few drops - the same amount of water that rests on the ledge all around the tub after a shower. So it's no emergency.

  • 4 years ago



    This is not the same model but the brass piece is similar - to give you an idea of what I'm describing. The nipple screws directly into there. The red rubber you can see is the stopper. In my case, the brass piece screws into a plastic housing within the metal spout frame. So cheaper than this one...

  • 4 years ago

    "Since it's plastic, I was under the impression that tape and/or pipe dope shouldn't be used. Am I wrong about that?"

    Yes, teflon on all threads. I would imagine the spout even came with a small roll of it.

  • 4 years ago

    It didn't come with tape. A quick Google search shows a whole lot of information about not using tape on plastic.


    In either case, I did try it and it didn't help. I'll wait for the new, useless cartridge to come in, then call Delta back and tell them that didn't fix it and hopefully get another rep on the phone who will just send me a new spout.

  • 4 years ago

    I don't see anything that says not to use tape on plastic. The only thing is the manufacturer of whatever product using 2 pieces of plastic to couple together may disallow it's use as with the tape as lubricant, you can over-torque the threads, rendering the threads to leak. But what other choice do you have at the point when threads are leaking without using any sealant or lubricant.

    Otherwise, some PTFE tape is specifically listed as compatible with ABS, PVC, CPVC, poly, nylon, etc. like Blue Monster or Slic-Tite. And, FWIW, Oatey does specify that pipe dope can be put over tape.

    Good luck.