Software
Houzz Logo Print
ben_ryan100

Should I be concerned about moisture damage?

4 years ago

Hello,


A year ago we had a contractor completely redo our master bathroom which included installing a new MAAX shower stall. Over the months I've noticed the baseboard on the right side of the shower appears to have some moisture damage. Though, after showers, I do not see or feel any water/moisture in this area. He siliconed both inside and outside along the vertical and horizontal shower rails here. Should I be worried there is some leak coming from behind the tile that is getting soaked up by the baseboard? Or is this from condensation/moisture in the air? Notice there is a bit of orange mildew along the lower portion of the grout line and the paint peeling off the baseboard.



On another note, on the other side of the shower stall which is up against the vanity, I noted that the contractor only siliconed the inside of the shower stall as he must have installed the vanity first, which limited his access to the outside of the shower stall. I've noticed there is some red mildew/bacteria that is growing along the rail and also on the bottom horizontal grout line sort of "spilling over" into the vanity:



After showers, there is no pools of water appearing; however, if I stick a narrow rod with a sponge at the end of it and run it along the rail, some moisture gets sucked up into the sponge. So clearly there is some moisture, but do I need to be concerned? Along the rail is more just unsightly; it's the mildew at the very end which I'm more concerned about as I do not want moisture getting sucked to the wall/floor via capillary action through the grout.


What irks me is that the manual for the shower stall specifically says to only silicone the outside of the shower stall (likely so if any moisture gets into the rails, it can spill back into the shower base). However, because the contractor installed the vanity first, he could only silicone the inside.


Any suggestions on how to proceed? Any way I can get the seams siliconed in such a tight space without having to remove the vanity/cut holes in the sides of it? Or is minimal moisture here safe as long as it isn't pooling? I just don't want a slow rot to occur.


Thanks in advance!


Ben


Comments (10)

  • 4 years ago

    Can you take a picture from further back so we get a better idea of where this is in context?

  • 4 years ago

    Oh yes of course. Sorry about that!

    So for the first issue, here is a photo taken further back. The only concern is just the part where the baseboard touches the shower surround.



    For the second issue, here is also a photo taken further back. As you can see how the shower glass is up against the vanity, and there is only a small gap in between.



  • 4 years ago

    I would contact the contractor. That's unacceptable and I think it will only get worse. Note I am not a professional

  • 4 years ago

    Definitely cause for concern… but don’t work up to much expectation for the contractors acceptance of blame.. a more diplomatic approach of “what will something like this cost”..will get it done quicker and hopefully less “costly” on other levels

  • 4 years ago

    You've kinda got a near impossible cleaning/maintenance issue with that vanity right against the shower stall Iike that.

  • 4 years ago

    Yeah, it's a small master bathroom so there was really no alternative. I just wish the contractor had completed the shower first the right way.


    I've already called him earlier in the year for some other issues and he kept saying yah he'd come take a look, but then would never come. I don't even mind paying a bit to fix it somehow I just don't know whether to try him again or just call like a local handyman.


    What's the best way to fix this?


  • 4 years ago

    Thanks palimpsest. Instead of redoing the whole thing, what do you think of cutting out a window or several access holes on the side of the vanity (that side has no drawers) along the bottom to create access to caulk properly along the shower base? Yes there would be unsightly hole(s) on that side of the vanity now (only visible if taking a shower), but at least the base would be caulked on the outside? I could slide a white 1x4 between the glass and vanity after to hide the gap/holes, and just remove it for routine cleaning/maintenance. Unless anyone has ever seen a super long caulking gun tip to reach back there.

  • 4 years ago

    "What's the best way to fix this?"


    Unfortunately without knowing how it was constructed and with what materials were used (cement board, waterproofing, etc.) a "fix" is really impossible to answer.

  • 4 years ago

    There while not be a good way to solve this problem in place…your pictures do not show enough to even be sure about any advice…other than to have the sink and cabinet removed…finish as you want. ..and moved over a little if possible…and re-install….once you get a tiny bit more space you will have to clean/dry that area with a wooden yardstick, wrapped with a cloth..no promises that it will not lead to much larger water problems in the future..