Software
Houzz Logo Print
filiz_seeborg

kitchen cabinet problem

4 years ago

Hello,

We got our kitchen renovated 4 years ago right after hurricane Harvey. I have noticed some separation of the cabinet frames from the glue lines for the past year or so which is very frustrating. They were made by a reputable carpenter and look really nice. He has always been very difficult to get hold of so I know I will need some repairs to be done by somebody else. Is this a problem that happens frequently or is this due to poor carpentry? How can it be prevented ? It will
Be very difficult to get a carpenter just for repairs like this. I appreciate your Recommendations.

Comments (12)

  • 4 years ago
    last modified: 4 years ago

    What is the humidity reading in your home? Is is 30-60% year round? If not, the wood will move too much snd that is what you get. Normal wood movement caused by excessive humidity swings is not covered under anyone’s warranty. And that is what you have. Normal wood movement that is ONLY caused by excessive humidity swings. There is no repair of that.

  • 4 years ago

    We live in Houston, TX. We keep our home temp at 77F year round and humidity 60%.

  • 4 years ago

    The physical evidence of the cabinets show otherwise. Either way, that is not a defect, and can not be repaired. You either live with, or you purchase new.

  • 4 years ago
    last modified: 4 years ago

    Its wood, it expands and contracts and that means it separates with a painted finish.

  • 4 years ago

    So is there no way that those areas can be filled in or glued again and painted ?

  • PRO
    4 years ago

    Get a color-matched putty stick and they'll disappear.

  • 4 years ago

    I’d be more upset with the unfilled nail holes and dents which were probably there to begin with. Might be best to ride it out a few more years and then get a complete new paint job which would include filling the holes and other proper prep work. Also the split joints could be caulked before the new paint.

  • 4 years ago

    I see your point but There were no nail holes before. The cabinets were made in 2018. It almost looks like as if it is shedding its putty and paint. How is that possible? I know they did primer before painting them as well. I agree with you about repainting and filling the holes etc.

  • 4 years ago

    I’m not so sure based on an indent with white paint vs. an indent with paint chipped off. See photo for what I believe was an existing bad prep job vs. a new dent. Perhaps with all the newness you didn’t notice the itty bitty unfilled holes and dents? Of course they are your cabinets and you are seeing them daily and should know best the original condition, I’m only giving an opinion based on what I see. It’s too bad because all that bothers me, but in life with daily use and several family members, damage is to be expected.

  • 4 years ago
    last modified: 4 years ago

    “Custom” is 𝐧𝐨𝐭 a synonym for quality. Despite what people are led to infer by the skilled craftsmanship connotation that the word worms into their brain. Custom just means built to a specification. That specification and build quality can be utter shite. Price 𝗱𝗼𝗲𝘀 correlate with quality, despite people searching for the upside down world where they get a cheap expenditure and receive a high quality product.

    Cabinets should not be caulked, or painted. And should have very little glue, especially for cross grain joints. The joinery is what hold those tight, not glue. There isn’t enough glue in the world to hold a cross grain joint tight without correct wood joinery and mechanical aids like dominos. A quality cabinet also has a multi stage coating process with an industrial wood coating, in a dedicated spray booth. Not latex paint on site over carpenter pocket screwed built— stuff. There is no repair. No fixing. Not when poor climate control, hard wear, and excessive water, accelerate the normal wood movement past the ability of the low quality joinery and coating film to hold.

  • 4 years ago

    So the best way to solve the problem
    Is to get new cabinetry later ? If that is the case can it be done without damaging the quartz as it will have to be removed ??

  • 4 years ago

    Sorry for so many questions. It is frustrating.