Software
Houzz Logo Print
jimbo1938

no spark on 445 JD

15 years ago

I have no spark oneither plug got battery voltage on both coils where do I go from there? Is there an ignition module on the 445?

Comments (24)

  • 15 years ago

    ***"I have battery voltage at both coils"***
    This engine has a magneto ignition system. There should not be 12 volts connected to the coils.
    The white wire on each coil is the "kill wire" to ground the coil when you want to stop it from making spark, thus killing the engine.
    If you really do have 12 volts at each coil, something has been rewired incorrectly, and the coils may have been damaged.

  • 15 years ago

    So what you are saying the little pulser coil on the flywheel is supposed to charge the ign coils
    this is on a little 445 garden tractor with Kawasaki FD620D engine

  • 15 years ago

    I think the pulser coil's job is to tell the module when to fire the coils. Here's a manual link that should help.

    Here is a link that might be useful: service manual

  • 15 years ago

    Jimbo, I offer an apology. Your FD620 is not magneto ignition.
    After going back and rechecking the Kaw manual I have, I noticed that it does not cover FD620 models.
    Thanks to tomplumb's link I looked at the schematic for FD620.
    Tomplumb is correct that the PULSER coil triggers the igniter module to fire the IGNITION coil at the proper time.
    The 12 volts side of the ignition coil is fed from the key switch, so if you are getting 12VDC at the coils, your trouble is going to be found either in the igniter module itself, or in a connector/wiring serving the igniter module.

    Looking at the schematic, the "Orange w/White tracer" wire feeds 12VDC to the igniter, so you need to check that you have 12VDC present on that wire when the key is in the RUN position.
    The "Black w/White tracer" wire of the igniter pigtail provides the igniter ground circuit with a connection to the tractor ground, so check that there is a ground present on the B w/W wire in the igniter pigtail.
    Hopefully you will just find a loose connector.
    If you have 12VDC and ground at the proper circuits of the ignitor pigtail and still no spark, your igniter is defective.
    Sorry about the erroneous info in my first reponse.
    I hope you will graciously ignore my mistake.
    Good luck.

  • 15 years ago

    Does the 445 have the infamous Time Delay Module that can cause ignition problems and do fail?

  • 15 years ago

    See schematic below.

    {{gwi:314510}}

  • 15 years ago

    Is that schematic from a Kawasaki Engine Manual or a JD Technical Manual?

    The Kawasaki manual will be a generic schematic as a stand alone engine and not reflect specific variations added or changed by the tractor manufacturer.

  • 15 years ago

    Well, to be sure......that is an excerpt from a Kaw manual.
    Post a copy from the JD manual and let's compare them.

  • 15 years ago

    Haven't got a JD tech manual for a 445, and they are not on the web for download, but I've see enough small engine manuals from the engine manufacturers to know that they only show the wiring for the engine proper and not as installed and wired in the application.

    For instance, there's no seat switch or RIO switch or parking brake switch in that wiring diagram because Kawasaki does not spec those safety switches but JD does in the application which that engine is installed.

    To satisfy your curiosity you can go the the Kohler or B&S web site and look at the engine manual wiring diagrams and compare them to an easy to find Sears manual or a Cub Cadet. you'll find that engine manufacturer's wiring diagrams do not reflect their engines installed and wired in the vehicle but rather wired as a stand alone powerplant.

    I have often read on this and other forums that the Timer Delay Module used in JDs in the ignition circuit is responsible for loss of one cylinder or loss of spark altogether.

  • 15 years ago

    I hope engine_tech will pipe in on this thread as he is often able to post the particulars on JD tractors and their proprietary version of the Kaw engines.

  • 15 years ago

    With respect Mownie, it's NOT a JD proprietary version of the Kaw engines and I apologize for not being able to explain it better but you are fixated on the wiring diagram of the engine as it sits on a workbench not as it is installed and wired in the OP's JD445.

    The simple fact is that a Kawasaki manual and wiring diagram ONLY reflects what Kawasaki supplies to their customers NOT the environment that the engine is installed in by their customers.

    Kawasaki can sell a particular engine to 10 manufacturers anf that engine might end up in a lawn tractor, an ATV, a boat, or on a log splitter. Ant tech literature that Kawasaki published ONLY reflects what they sell to an OEM in a crate NOT what the OEM does with the engine. That tech literature comes from the manufacturer of the final product.

  • 15 years ago

    Yes mownie your apology is very much accepted I make more mistakes than anyone, I do thank everyone for thier help my trouble started when it blew the timing gear which I have replaced when I put the engine back in I mistakenly hooked the ground wire up to the starter terminal so it is no telling what I may have blown. the shemmatic will help tremendously.

  • 15 years ago

    Thanks fellows te print out will help tremendously mownie apology accepted I make more mistakes than anyone The tractor blew the timing gear which I have replaced when I put the engine back in the tractor I hooked the black ground wire to the starter terminal instead of engine ground so no telling what I have destroyed Thanks to all

  • 15 years ago

    justalurker, when I was typing my last post above, I was thinking of "the proprietary John Deere wiring/controls added to the Kaw engine", or at least the gist of that.
    I see how it came out sounding like I was saying a "special engine" built solely for John Deere.

  • 15 years ago

    I have traced the problem down to the control module and the price of a new one is $928.42, I am wondedring if a used one or rebuilt one is possible, I am a retired forklift mechanic and we sent the control cards in for rebuild at about half the cost of a new one.

  • 15 years ago

    jimbo,

    Before you fork over nearly a kilobuck for a new control module get a JD wiring diagram and make sure there's nothing else in the ignition circuit that is causing this problem...

    You can buy a Technical Manual for $75 on CD and it will have the complete JD wiring diagram and should have the troubleshooting procedure for the control module.

    Get your 445's serial number and look here... http://techpubs.deere.com/deere/TechPubSearch.aspx?Model=445&Language=English

  • 15 years ago

    Well justalurker I have a nieghbor that retired from JD and he came over with the tech manual we made all the checks and everything checks good it suggested to replace the control with a known good one if that corrects the problem then change it. I wish I could borrow a known good one.

  • 15 years ago

    "I have a neighbor that retired from JD and he came over with the tech manual we made all the checks"

    You didn't post that so how would we know?

  • 15 years ago

    I'm sorry he came over after the post was made and you all had helped me I had forgot that he did work for JD many years ago. we don't visit that much Sorry for the misunderstanding

  • 15 years ago

    Lots of people read these threads to help themselves so omissions of important info or diagnostic steps has a ripple effect.

    Let us know what you decide.

  • 15 years ago

    Many thanks to all that helped me I got real lucky and found a used one on Ebay it is on it's way I will post the outcome.

  • 7 years ago

    was the outcome ever posted?

  • 7 years ago

    My 445 doesn't appear to have a the Time Delay Module that I can find. I have replaced both coils( the originals were still on the mower. I have power to the coils (both) no spark. I also replaced the pulsing coil pickup still no different. History is, It ran perfectly in October while in use then I noticed a "sputter" under load...finished aerating the yard parked and thought " I may have a coil going bad...I'll check it out when the season starts back up"...when to start 2 weeks ago and no spark. It has the fuel injected Kawasaki motor production date 10/98. Not sure if metal or plastic gear but removed valve cover on the right side (if sitting on the mower) valves are opening and closing.


  • 4 years ago

    Did you ever figure your issue with no spark??

Sponsored