go to rustytiller.com technicl page tiller identifcation tiller manual down load may be this will help

I have a Montgomery Wards Rototiller model GIL 1565E. I'm looking for the pto/ clutch assembly. This is the arm w/ pulleys that mounts on the engine and the linkage. If anyone has the parts to sell, let me know.

OK...I've gone to www.rustytiller.com and found the owners guide for my MW 1580F rototiller. However, the B&S page does not return any manuals for the listed engine (130202-0135-07) and I need an engine part. Specifically, the rewind spring is not strong enough to rewind the pull cord against the shaft. Any ideas, different/similar engine numbers and/or rewind spring parts number?

Thanks,
Ebenezer

Briggs doesn't say so, but use 130202-0135-99 to get the IPL. Your spring is 294303 and should be $4 or $5.

I doubt if the spring is bad, and there is only one spring. You might want to get one or two more turns on the starter sheave to increase tension, but more likely you need to check for drag and binding, which is causing your rope to fail to retract properly.

Is the starter clutch in good condition? Does the rope rub on the housing? Is the sheave free to rotate without binding? Do you have too much rope? Did someone replace rope with larger diameter (thicker)?

Hello My father is looking for a worm wheel for a
model Gil 1570b part # 1004 can someone please help me
find this part my e-mail btakscruggs@yahoo.com

I have a white's ranger. It looks like a gilson parts are worn out in the gear case any idea where to get parts?

Woody, I would like to get a copy of the owners manual with a parts list for the GIL-1580-G tiller, and would be glad to pay for postage and copying. We have the same tiller, just no manual. Please let me now how to receive this copy. Thank you.

Briggs n stratton
model 92902
type 2067-01
code 80020505

I have both the Briggs 130202 part breakdown and the GIL 1580 owners manual in pdf. Just email me and I'll send you a copy.

Kenny_H,

Please send me a copy of B&S 130202 and the GIL 1580 manuals. I need them to work with my tiller. Thanks!

Kenny_H

My email address is

kctme@ureach.com

Thanks!

What type of spark plug does the 5 horse B&S require?

Any additional info will be welcomed

whatfour1@yahoo.com

If anyone has a repair manual for the Model Gil 1589A, or anything close, can you email it to me at whatfour1@yahoo.com .

If you have a repair manual for the engine, a 5 hp briggs and stratton Power Kraft that would be welcome also.

If you want some money for it let me know, I am trying to get this relic to go, and without the needed information it is real slow.

thanks

Go join Gilson yahoo groups dot com they small amount info there on tillers its gilson tractor group ask question there be best place Gilson was made for mongomeryward all Gil numbers mean Gilson.

HI,

I am seeking a diagram, photo, pdf file, for any gilson rototiller I have a 1575E I need help with the pulley system I bought this used and everything works fine except the pulleys? The rustytiller.com website sucks! I don't know if anyone else has had problems but it seems to be a add site with no use full information.

any help appreciated Thanks!

i need pats manuel for gil 1545b 5hp roto tiller

i have a front tines rotortiller that was bought at Montgomery Wards.
It does not have a belt to pull the tines, but looks more like some kind of a clutch. the forks going to the clutch has worn down alot, this does not let the clutch engage. Anyone know anything about this setup and where I can get parts for it?

I need a worm wheel (Part #1626) for a GIL-1576A
Rototiller. I have the owner's guide for this particular
model.

Same part is used in a 1558A 8hp tiller. Unfortunately this has been NLA for many years. Only chance is to find a similar junker as a donor.

The worm gear to my GIL 1580F is gone(worn out).
Does anybody have the manual, the part number, or a worm gear for this model? Will the worm gears interchange from 1580H to 1580F?

Same availability problem with 1004 Worm Wheel. NLA. Actually more common than the 1626 in earlier posting. However, only answer I know of is to find old donor machine. Lastly, will interchange across all 1580 sub models, and is also common to 1565, 1572, 1575, and 1589 tillers.

I have a White Ranger with bad gear teeth, it also is a 5 horse B&S. My questions are where on the tiller is the Gil model no? Is it stamped on the frame? Where can I find a repair manual? and a set of gears? thanks.

my lawn tractor pull around rototiller needs tines model#gil-33095A hole pattern 3/8" in dia 1 1/8 apart approx length 5 1/2"

I need the belt sizes for gilson model # 1575E...Please someone help me out.....Thanks, Jimmy

If someone can email me a pdf or something of the manual showing the part numbers for the belts for a GIl 1580-G and how they are routed i'd appreciate it. if someone has kenny_h's email please let me know so i can get the manual. thanks
tidus211@hotmail.com

Well, www.rustytiller.com has given up and gone away.

Unfortunately, they left before I got a copy of the manual for my Montgomery-Wards rototiller. It is a model 1580i (or 1) made by Gilson.

If anyone has a copy of the manual for a model 1580 from rustytiller.com (or anywhere else) please email it to me.

Thanks!

WOW, Double WOW-

I got an email with the manual attached today. Way cool!

If anyone else needs a copy I'll sure send it along.

Thanks Again!!

i'm a new owner of a gil 39012B wards tiller,in need of a owners manual,any help would be apreciated,thanks

Have toy checked the site below? I just saw it vs trying to download. Any specific questions that you might get help on while looking for a manual? I feel I have done some welding repairs on one or two. Loger
http://www.imarksweb.net/book/montgomery+ward+tiller+gil+1570b/

@dropdeadzoom

Kind of hard to help when you don't post an email address.

See the guys above you.

my e-mail address is nathan_shields@yahoo.com

Kenny_H

Do you still have the manual PDF for montgomery wards tiller gil 1580-g? If so, could you send it along to:

daniel.newham7@gmail.com

Many thanks! My first tiller project and I'm 95% done but can't figure out the throttle assembly under/behind the gas tank.

Very best -
Daniel

I have a Montgomery Ward tiller Model GIL 1565 G that I am needing information on. The seals are leaking were the tine are. If anyone have part number for these seals or even a owner manual would be a great help. I have look for a pdf of the manual so I can get part number but can not find it. Thanks for any help you can give me. If you have a pdf of the manual you can send it to dewaynep@windstream.net

Please post some pics or links to the Wards tiller (lazy me and little search time) and I might be able to help with some B&S specs vs gearboxes (I have old gen small engine manuals from the 70s). I had a Wards tiller in the 70s with a hor shaft, B&S and cast iron gearbox/body that was very tuff and good. I also found the same version gearbox with a ver shaft on a curb. The owned said it runs but I d/n find it as friendly as the hor shaft and put it back on the curb. We h/n needed a tiller since the mid 90s and I have too much STUFF. loger

I have a Mongomery Wards Rototiller GIL 1580 F all heck has happened to my 30 year old never break tiller.(Tilled the garden as I always have for the last 10 years, when everything broke. All belts are damaged, gasket between carb and tank is leaking, the diff is leaking oil everywhere.) I need all kinds of parts and a manual cannot find anywhere. I love this tiller and need to save it. Any help would be great Thanks.

I too have an old Gilson Tiller and in need of a diagram that shows how the pulley system works. It is a GIL 1575C model. My Dad, God rest his soul, gave it to me years ago after he had disassembled it. He didn't have a manual and I would appreciate it if anyone could email me a copy that I could use to get part numbers and the layout of pulley system.

I have a 1500A Montgomery Ward Front tine tiller.Does anyone have any info on this or a parts diagram??

Lee1575,

Can't help you with a manual if you don't enable the "Send my an Email" feature on your Member's Page.

ggoyeneche, Sorry about the email address. I went and changed the option for it.

Thanks

I see some other people have been successful in finding a manual for a Gilson Model 1580G Tiller. I was hoping someone could also email me a copy of this manual as well. I was just given one today that hasn't been used in over 10 years but it was well taken care of and it still seems to run good. I'd like to tune it up a bit and have no idea how much oil and such to put back in it.

HELLO WOODY, I WOULD A COPY OF THE MANUAL AND PARTS LIST FOR THE GIL-1580-G MACHINE,HOW MUCH WILL IT COST TO COPY AND SEND TO UTICA NEW YORK,13502,PLEASE REPLY BACK THANKS.

HELLO, WOODY, I WOULD LIKE A COPY OF THE MANUAL AND PARTS LIST FOR THE GIL-1580-G MACHINE,HOW MUCH WILL IT COST TO COPY AND SEND TO UTICA NEW YORK,13502,PLEASE E-MAIL ME BACK AT mikey135@verizon.net,please reply back thanks.

I could really use a pdf copy of the manual for a GIL 1580 G Tiller, The rear belt is missing and I need to figure out the routing of the belt. Thank You in advance for any help!
bigfish80031@hotmail.com

Hi al - need manual for gil1580 G and the 5hp Briggs and Stratton engine - help! And thank you

What do u need to do? I ask because i have a WesternAuto tiller. it differs some but major parts are the same with other models. Maybe my copy will answer your question.

I have a Montgomery ward tiller Gil 1580 f. Does anyone know what size belt it takes and where to find one?

The forward (inner) belt is Gilson p/n 1110 and is 1/2 in (4L) x 35 in long. Reverse (outer) belt is p/n 6163 and is 3/8 in (3L) x 37 in long. Suppliers include Kaman Bearing, Bearings and Drives, VBeltGuys, and VBeltsforLess.

If ANYONE has been successful getting a Gil 1580 f owner's/repair manual and can email me a copy I'd sure appreciate it. Even a 1580e or 1580 g may be close? Gonna try to direct email to some of the members who left their email also. Thanks.

jana_ouimet@hotmail.com

Have you tried adjusting the points? That's what I did to mine and it started right up after adjustment

Kenny_H

Do you still have the manual PDF for montgomery wards tiller gil 1580-g? If so, could you send a copy me at:

onscenenow@aol.com

Thank You so much, Steve