Software
Houzz Logo Print
appaloosa909

where to start?

17 years ago

I have a mess!!

I started to re-caulk my tub and 3 piece surround when I realized that the mold/mildew was inside or behind the caulk. After removing the old caulk, I bleached and realized that the back wall had popped off (glue gave out??) anyway I laid in the tub with a flashlight and looked underneath and saw (and smelled) mold.

I removed the 3 piece unit and saw that 90% of the glue wasn't stuck anymore and that more than 1/2 the wall with the spigot and the long side wall (that has a window in it) was covered with rot and mold. I ended up taking out the backboard and found the wood surrounding the window rotted(even the metal stripping is rusted and some is gone), the wood surrounding the pipes full of mold and the entire base that meets the tub rotten.

I have known for some time I was going to have to deal with this bathroom, but I was re-finishing wood floors and painting the downstairs. I'm handy but have never tiled before.

My question.... now what?

I know I need to have the wood surrounding the window replaced.

I know I need to replace the window.

How do I get rid of the mold on the wood thats not rotted?

do I replace it too?

Can I paint the tub white?

What kind of sheetrock goes in the tub area? Cement board? Do I use that in the entire bathroom? ( I'm going to have to remove the tile in whole bathroom including the floor anyway)

Do I tile the tub area first then the floor? or vice versa?

Toilet is fairly new but want to replace sink, medicine cabnit and vanity.

I'm overwhelmed!!!

Thanks for reading

Andrea

Comments (2)

  • 17 years ago

    I'm so sorry that this is happening to you, and how can you NOT be overwhelmed! I think it's probably really dependent on what kind of mold it is because from what I understand there are some types of mold that just never go away. That said, if it were me, and I could afford to, I'd probably just go ahead and replace anything with mold on it. But if your not in a financial position to do that, why not try bleaching the wood that isn't rotted first. Use a couple of really heavy applications and let the wood dry out completely.

    In regards to the tub, lots of people get them re glazed or have a new liner installed and from what I understand, it's a lot less expensive than replacing it.

    Now in regards to your drywall and tile questions, if you do a search in the search box for Bill Vincent and/or Mongo you will find a wealth of information, if you can't find the answers to your questions, I'd do a new post addressed to Bill or Mongo at ask them and I'm sure they'll be very responsive to you.

    Good luck on your project Andrea, take a deep breath and don't panic, just focus on one step at a time, it may take a while, but in the end it always works out. -- Lukki

  • 17 years ago

    Somewhat of a different scenario/problem than what we had here, but we too had mold and.....mushrooms! Gross! We didn't have the 3 piece shower surround, but we did have an old steel tub, and it was around the bottom of the tub, behind the 1" "gasp" of silicone that had been used to hold all the "garbage of a wall" together. We weren't financially able to rip out our only bathroom at the time, so we removed all the silicone, trim bits, and baseboard near the area. Ran fans directly into the area for a few days, and then sprayed with straight household bleach. It took longer for the memories of the sprouting mushrooms to go away, than for the musty smell of mold!

    Ah well.. we're done now, but I'd sure advise not letting anything that has been/is wet, staying in your new build. When we tore ours out in December, I was mildly surprised that the mold wasn't more pervasive. Just seemed to have been kept to the one end of the tub around the taps/faucets/silcone zone.

    Good luck, enjoy the new bathroom. Oh, and remember... it won't be pretty along the way, but wow! is it worth the wait/mess/sleepless nights!

    Kym