Software
Houzz Logo Print
monsoon99_gw

Building a new home - Electrical question

18 years ago

I am a homeowner going through a first time home building experience. Today, the electrical contractor told me next week we will sit and look at the electric plans drawn up by architect to see where everything goes and if wanted anything to add. It is hard enough deciphering the electric plans, leave alone come up with new ideas. I wanted your input on what I should be looking at, what to include, what is good electrical decision you made in your remodel or building project to make your life easier? I do know to ask for outlets inside bathroom drawers for hairdryers. Your help is appreciated.

Comments (20)

  • 18 years ago

    Put an electrical outlet next to each toilet (heated toilet seat, washlet seat, etc.). Our code inspector got a kick out of that one.

    Electric outlet under the sink. Even if you won't have a disposal (we don't) it's good to have it there un case you want to add a insta-hot or cold water dispenser.

    Obviously think about furniture location and how you will use each room. Make sure the vac outlets (assume you are doing central vac) won't end up behind furniture.

    LOTS of outlets behind the primary TV. You never seem to have enough.

    Plan a place to charge ipods, cell phones, etc. We have a built-in in the mudroom with electric outlets above the shelf.

    Outlet built into the fireplace mantel (set flush in the top).

    Put a GFI outlet where the iron will go (this may be code, not sure).

    In addition to the places required by code, put smoke/fire detectors where it makes sense. For example, they are not required in laundry rooms, but dryers cause a lot of fires, so we put a smoke detector in the laundry room.

    Plan your sconce heights. Make sure the electrician understands that designated light locations must be exact (this is often an issue over bathroom sinks where lots of people complain things are off center).

    Decide where you will have built-in medicine cabinets and don't allow plumbing, vent or electrical lines there (we went to hang a mirror over a sink recently and hit the vent for the sink, that was was supposed to be obstruction free, good thing I didn't do a cabinet).

    Run PVC pipes from the basement to the attic (capped at top and bottom for fire reasons) in case you want to finish the attic later.

    Use a fan-rated light box anywhere you think you might end up with a fan someday (we did this in all bedrooms).

    Plan outlet locations for your kitchen island. This can get tricky depending on how strict your code officer is. ask the electrician for guidance on what is required and then determine the least ugly way to comply.

    That's all I can think of right now. I'm sure others will chime in.

    p.s. Outlets inside drawers are against code in some areas, like mine.

  • 18 years ago

    Sue36 has lots of great ideas, including:

    > Put a GFI outlet where the iron will go (this may be code, not sure)

    Consider an Iron-A-Way (http://ironaway.com) - which has a built-in outlet. Leave a drop for it. Interestingly my wifes iron is about 1/2" too wide for the Iron-A-Ways built in storage compartment though.

    A few more:

    Put in a network hub panel (Leviton, Channel Master, etc.), with a power outlet. Run some CAT-5E cable to places where you will want computers. (E.g, home office, kids rooms, etc.) An outlet up high above it for a wireless networking router.

    Run a bunch of RG-6 (TV coax) from the network hub to wherever needed too. If you want to prewire for satellite feed, you need two RG-6 and two CAT-5E per location.

    A "service light" and outlet(s) in the attic.

    Outdoor outlets by the garage and various other locations (patio, outdoor kitchen, etc.)

    Security system. (Check your homeowners insurance company. Ours gives a 5-10% discount - depending on whether it is connected to an outside service or not.)

    Extra power outlets where computers might go. As with entertainment systems, it seems one can never have enough. And as with entertainment systems, it is good if these can be on dedicated circuits.

    Three-way switches in bedrooms for lights - next to the door, and next to the bed.

    Lots of outlets in the garage.

  • 18 years ago

    Good start above. Here's my two cents..

    - Sconces are always a bit tough because the type of fixture will determine height. Generally, putting the bulb/globe at about 65" works well.

    - Except for garages, there is generally no code specifying the heights of switches and receptacles above finished floor (AFF). I placed my switches a few inches lower than normal but you have a lot of flexibility here. You may want to refer to ADA (American Disabilities Act) specs if you are concerned about accessibility.

    - My electrician recommended a receptacle below each switch in a room. This is a good idea as furniture is rarely placed close enough to a door frame to block access.

    - Install ceiling-mounted single receptacles for automatic garage door openers. Use quad receptacles, rated for 20A, on garage walls.

    - Place receptacles in the eaves/soffitts at each corner of your house for Christmas lights, roof heating elements, etc.

    - Special care must be taken if using pocket doors and a receptacle is required in the wall cavity.

    - Go beyond code for outside recptacles and place a receptacle near each corner of your house in front and back. Treat an attached garage separately and place at least one receptacle on front and back. Receptacles for attached decks can be placed on railing posts to reduce penetrations in your exterior walls.

    - Many inspectors now like to see 12 gauge wire installed for all general purpose circuits but, per code, circuits terminated with 15A (amp) breakers can use 14 gauge wire. 12 gauge is thicker and is required for 20A circuits (bath & kitchen countertops) but provides a wider margin of safety for 15A circuits. Using 12 gauge throughout also gives you the flexibility to upgrade a circuit to 20A.

    - I never heard of drawer receptacles before. I assume this is a receptacle surface-mounted in the drawer with an electric wire whip with enough slack to allow the drawer to fully open. I would advise against it. Too much wear and tear on the wire as you open/close drawer (even if code OKs it) and the wire cannot be readily seen for a visual inspection.

    - There are special code rqmts for placement of receptacles above certain type of baseboard heaters. Some systems will require coordination with your HVAC installer.

    I hope this helps...T

  • 18 years ago

    Let's see what hasn't been said.

    Think about switches; where and how many and what each will control. (Who was it commented that she lights up the whole front and back yards just to take the trash out? Remember to have separate switches for separate areas, outside as well as inside.)

    Try to unify the placement of light switches: X inches from floor and X inches from door knob. ALL of them. It is exasperating to reach one place to light the hall and then another place to light the room. Do not depend on the electrician to place them reasonably!

    Put more outlets in the kitchen than you think you will ever use; at least one for each gadget plus a few more. The microwave should have its own outlet. Make at least one counter-height cabinet heat-proof, and have outlets available for toaster, coffeemaker, crockpot. It's nice to be able to safely close the door on the gadgets when not in use. Make sure the gadget outlets are on a separate line from everything else. Ask for an outlet (for refrig and for freezer) which as an LED warning lamp. A glance at the lamp will reassure you the electric is running.

    Also in the kitchen. Place lights so that there is no shadow over your working area. That sounds simplistic, but I've seen a lot of lights behind the cook instead of in front and below eye-level.

    CFLs are smart, but you can't use them with dimmers. Think carefully about where you will actually use dimmers.

    Put a small light inside every closet. A small CFL or large nightlight does fine and it's great to see whether you are getting the navy blue or the black coat. Use one with a door switch for on/off.

    Put a light over the washing machine and another directly over the folding surface.

    If you can afford it, have a separate wire run for a night light in every room, hall and stairway with a single master timer switch.

    Put a night light over each toilet. Use a very quiet, low-powered vent fan over each toilet -- you don't need one that will suck up the bathmat, just one that will move odors (and bath steam) outside.

    Put an outlet under each sink. The plumber will thank you. Not electrical, but be sure every sink has a cut-off valve in both lines. Your wallet will thank you when it gets the plumber's bill.

    Put a light over each tub/shower. Make sure it's rated for outdoors or marine use, and is well-caulked.

    Make sure the HVAC has its needs met.

    Be sure stairs are well lit.

    Put a non-electrical light over the fuse/switch master box. (The type that is plugged in and the turns on whenever the electricity goes out.) Those are also good for emergency lighting of stairways.

    Keep count of how many outlet and switchplates will be needed, their configuration, and whether they are utility or should be fancier. Don't faint when pricing these.

  • 18 years ago

    I have seen the cords of too many hair dryers suddenly short with a burst of sparks from repetitive wear and hair in the nozzle catch fire to put one in a drawer while still plugged in.

    This has been discussed at great length elsewhere with convenience generally winning out over safety but each homeowner should use their own judgment.

  • 18 years ago

    I've got one I've never seen before.

    I put an emergency light like you would see in an office building near my electrical panel. I have a manual generator transfer switch so I figured it would be useful to see what I was doing. Even if you didn't it might be nice to have light near the panel if your power goes out on the off chance it is one of your breakers.

    The fixture was pretty cheap (about $20) and not much additional to install since you are right at the panel.

  • 18 years ago

    I saw one setup which had the hairdryers hanging inside a wall cabinet behind the mirror; looked like it might have been set inside the studs. I don't know the safety factor of hanging a hot dryer, but the cabinet itself was metal (and deeper than most medicine cabinets).

  • 18 years ago

    All electrical devices connected to a power source should be treated as if they could turn on accidentally or short at any time. Think hard before trusting appliance switches and wiring insulation to protect your property and your life in a cluttered bathroom drawer.

  • 18 years ago

    I have never understood why people would want to have an outlet inside a drawer or a cabinet for hairdryers/curling irons/etc. Is it really that difficult to pull it out and plug it in? It adds maybe 10 seconds to the amount of time it would take to get ready. Plus, what happens while you're using it...the drawer or door is open or partially open? This is an absolutely useless "convenience" item and a dangerous one...IMO.

  • 18 years ago

    Thank you very much for your wonderful suggestions that I would have never thought of myself. What was life like before the internet and forums like this? I really appreciate it and now realize how much there is to think about.

  • 18 years ago

    Anyone not willing to pull a hair dryer out and plug it into a gfci outlet to be safe is insane. If you dont have gfci recepts in your bath, laundry, kitchen, anywhere near water sources, think seriously about having a licensed/reputable electrician do that for you. Jeez!

  • 18 years ago

    This followup question has to do with what to consider with other systems the electrician would install: home security, audio system, central vaccum, telephone, cable, etc. Thanks.

  • 18 years ago

    We put outlets in the soffits for Christmas lights. I wish that we had put an outlet in the floor under the kitchen table so that when I use the table for serving large groups of kids I could plug in crock pots/nescos/etc. If you have pantry be sure to put at least one outlet in there. If you have an appliance garage, be sure to put at least one outlet in there so that you can keep appliances plugged in so that you just need to slide them in/out to use them. If you are getting a built in ironing board, consider putting an outlet in the cabinet.

  • 18 years ago

    We put an outlet under each window and wired the top receptacle of all of them to one switch so that at Christmas when we put candles in the windows, the flip of one switch turns them all on as opposed to unplugging/plugging each one.

  • 18 years ago

    Lots of good suggestions have already been posted. Here are a couple I don't think anyone has mentioned...

    Lights in our walk-in closets will be wired to door switches so that the light comes on automatically when you open the door and goes out automatically when you close the door - like a refrigerator light. I'm hoping this set-up will also help me train DH to CLOSE his closet door instead of leaving it standing open all the time!

    Several outlets in the soffits way around the house for plugging in Christmas lights - all are wired to a single switch for ease in turning lights on/off.

    Extra lights in our stick-built attic space with a switch by the access door so we don't have to use flashlights to find stuff stored up there. Everyplace I've ever lived had one light in the attic at most. Even with it on, the thing you're looking for is always in some other corner that is dark.

    Mirror defoggers in the bathrooms (a very inexpensive luxury!)

    Outdoor lights specially positioned for reading when one is sitting on our porch swing.

    A floodlight positioned to shine up and into the stained glass window that is in our the stairwell so we can enjoy it at night.

    Lots of extra electrical outlets around the exterior of the house.

  • 18 years ago

    The only one I can add is a three-way switch for the bedroom light that you can hit while you're in bed.

    Way up in the good suggestions above, there was mention of 12 gauge wire... it is good in some circumstances, but I'd encourage you to discuss it with your electrician to see if the benefits to you outweigh the costs.

  • 18 years ago

    monsoon99, The hairdryer in the drawer, although off topic, is a safety concern that might benefit other readers of the thread. It's always relevant when safety is a concern. Sorry for the hijack, but felt it was important.

  • 18 years ago

    > This followup question has to do with what to consider with other systems the electrician would install: home security, audio system, central vaccum, telephone, cable, etc...

    If you want to go 'hog wild', check out the following link. And note that if you go beyond a few basic phone outlets, your electrician may defer to a specialty 'low voltage' contractor.

    I was much more restrained in our house.

    I put a lot of CAT-5E. Basically each room has 2 outlets with 2 CAT-5E in each. The CAT-5E wires can be used either for phone or ethernet. Each room has at least one RG-6. A few locations have satelite prewire. All lead to a central network hub panel. And rough-in wiring leading to the roof and phone/cable service.

    Here is a link that might be useful: Hometech FAQ: I am remodeling or building a house, what wire should I put in?

  • 18 years ago

    Well, I remembered another couple locations:

    If you have crawlspace, whether attics or beneath the house/garage, enough light fixtures so that a flashlight isn't needed. (Says someone with an 'L'-shaped crawlspace and it's dark as midnight in the far wing.)

    A master switch in the MB [closet], to control all the exterior lights. Also read someone suggested same location switch for the exterior decorative lighting, which is usually separate from the floods, etc.

  • 18 years ago

    Something else I forgot about is Lutron's radio-frequency controlled system. By upgrading key hard-wired switches you can add wireless remote switches or master controllers for additional lighting control. Go to lutron.com and check out their Aurora system.