Software
Houzz Logo Print
katy_lou_gw

Hood order - any last minute changes?

13 years ago

We need to go ahead an order our hood. It is being custom done by Abakka with remote blower (just the insert- surround will be done by local metal smith) due to a window behind the stove, the hood wil be place higher than normal. So we are attempting to compensate for that with a larger capture area

Stove 30" blue star

Hood liner dimensions - mounted to wall / window header trim about an inch out from wall -

38.25" length (so with shell, 40")
25" deep (with shell, 27") from wall / back of stove
10" duct
External 1400 blower mounted on roof - but not very short duct run as
Roof is directly over kitchen there.
Any changes?

Comments (6)

  • 13 years ago

    We have an Abakka blower too. Ours is also roof mounted right above the kitchen. You might want to see if you should do the noise reduction kit. Here is another thing about the duct. The noise reduction kit has to be in a section of the duct that is horizontal to actually impact the sound waves. So plan the duct run carefully even if it is short.

  • 13 years ago

    It'll be like 8" short or maybe less so no room
    For the muffler. How loud is yours?

  • 13 years ago

    Our kitchen is not done yet but I went to someone's house who had the 1200 abakka and a similar setup. Our hood is 8 ft from the roof as well. We have a 1600 cfm unit connected to a 57" modernaire. After talking to abakka and modernaire, we had the HVAC guy offset the blower so that we could do the quiet kit. The issue was that we have an old not very insulated house and we do have some hearing problems in the family as well (older people losing hearing). I am hoping this works well. I am mentioning this as it took some effort over couple of weeks to educate myself and talk to abakka, talk to modernaire, talk to GC who talked to the HVAC guy etc. If you have not already, please post in the appliances forum where the hardcore, super knowledgeable ventilation guys hang out. You should get some good advice there.

  • 13 years ago

    i have a 36 inch range with a 1200 blower mounted on the roof, and at times think i could have used the 900 instead. my hood is 40 inches. Just curious as to why 1400 cfm for a 30 inch stove? being directly above you are bound to hear noise.
    i use my hood on the lowest setting usually and it does a great job.

  • 13 years ago

    It will need to be mounted at 7' so higher than normal - and variable speed so the hope would be that we could just have it turned down a bit

    This post was edited by katy-lou on Sat, Jan 5, 13 at 12:21

  • 13 years ago

    Having overkill cfm capacity with variable fan speed is the best way with residential targeted fans to get sufficient air flow rate along with lowered noise, particularly if a muffler/silencer cannot be fitted. And when the need arises to burn a pan of bacon, the excess capacity will no longer be excess. However, higher air flow capacity will drive up the cost of make-up air capacity.

    The larger hood aperture is just what is needed to compensate for higher mounting to obtain good capture, and along with the larger aperture area must go larger cfm to keep the velocity of the air at the hood aperture as high as it needs to be for containment. Compensation for height with size and flow rate will be fine in ideal circumstances, but if there are cross drafts the capture may be reduced from that obtained with a lower hood.

    I don't know what is in Abakka's quiet kit, but am unaware of any acoustic property that depends on horizontal vs. vertical mounting. I do not believe that Fantech's silencers care about orientation, although hanging them can be more difficult if near vertical.

    kas

Sponsored
Bella Casa LLC
Average rating: 5 out of 5 stars17 Reviews
The Leading Interior Design Studio in Franklin County