Software
Houzz Logo Print
chris45ny

Tile/hardwood floor edging question

16 years ago

Also posted this in the flooring forum but there's more traffic here. Kitchen open to DR. DR has hardwood. Kitchen will have tile. I would like the transition between the 2 floors to be as even as possible. Is there anything that could be used that would go with white oak and with Crossville's strong series tile?? DH showed me tile edging strips at Lowes that are either brass/gold or silver in color. Can I find something better to match the 2 floor colors?? TIA.

Comments (19)

  • 16 years ago

    Can't you use a oak saddle or reducer or whatever is needed to join them? It can be stained to match the oak. Pullllleze avoid the metal strips! (You know that, of course! :)

  • 16 years ago

    The problem with using a reducer is that it won't make an even transition between the 2 floors. We had that when the hardwood was first installed but I want something more flat and even between the 2 surfaces. The metal strip (not so pretty) is almost flat with the 2 floors. DH thinks maybe we should just caulk it??? I think I'm going to have an ulcer before this remodel is done!!!!!

  • 16 years ago

    Perhaps I should be clearer. The hardwood floor and tile floor will be equal in height.

  • 16 years ago

    Mine's grouted between my bathroom tile floor and my hardwood. I don't know if that's how it's typically done but I asked my contractor to make it as seamless as possible since I didn't want any of those transition strips etc. My floors are also the same height. I think it looks fine but if I did it again I'd ask for caulk since the wood floor is expanding and contracting a lot with temperature/humidity flucuations and there's a small gap between the wood and the grout now. Of course when the floor expands again it should fill the small gap, but I imagine caulk might be a better way to go.

  • 16 years ago

    All you need to do is leave a 1/8" joint between the two surfaces and caulk it with the siliconized latex made to match the grout.

  • 16 years ago

    Our hardwood and tile are even height and there is no transition strip. Ours is done similarly to Bill's picture, except we didn't do the trim piece along the edge.

  • 16 years ago

    The only reason for the end board is you can not butt the ends of hardwood strips against another flooring surface. It must be the side of a board. If the tile were running up against the side of the hardwood as it were laid, then you're right-- there'd be no need for the trim piece.

  • 16 years ago

    There we go! Mine looks just like the pic Bill posted.

  • 16 years ago

    Bill-guess DH was right when he mentioned the caulk but I may want to do that strip of wood like you have in the picture. Thanks so much for the pictures and the explanation.

    And thanks to everyone else who replied with advice!!!

  • 16 years ago

    Mine is like Bill's photo

  • 16 years ago

    We used a piece of granite...but we step down into our sunroom.

  • 16 years ago

    If there's any kind of height discrepancy, I agree-- some kind of transition needs to be used. If not, though, a third material, atleast in my mind, clutters the appearance.

  • 16 years ago

    Bill-just got back from Tiles International which is where we bought the floor tile, grout, etc. Per their recommendation for our situation we ended up buying the Laticrete Latasil to match in the toasted almond. The grout we got is also by Laticrete-permacolor. The heights of both floors will be even so DH has decided to just do the caulk as you had recommended. Thanks so much.

  • 16 years ago

    You're welcome. Just make sure if you're using the Latisil, that you tape off the edges and tool the joint. That stuff is 100% pure silicone, and can not be washed off.

  • 16 years ago

    Here is mine. sharaz

    Here is a link that might be useful: th_011 jpg

  • 16 years ago

    Finally I, learn how to put a picture in my post sharaz

    Here is a link that might be useful: th_011 jpg

  • 16 years ago

    shar-az Glad to hear you are able to post pics in your post. It's easy once you get the hang of it. Love how your two floors look. We are going to have a similar look, color wise. DH will start work after Easter so will post pics when it's done. Thanks again everyone!!

  • 16 years ago

    Excellent photo, Bill. I'm keeping that for future reference.

  • 9 years ago

    Can you suggest which caulking to use for this (tile to hardwood transition - hardwood is floating and is deep red in color) . If you have a pointed to the caulking , would appreciate it (so many of them out there )