Software
Houzz Logo Print
hzdeleted_20103024

Replacing Outdoor Receptacle Cover

10 years ago
last modified: 10 years ago

I have a GFCI horizontal 1-gang receptacle on my patio that has a GamPak weatherproof die-cast metal receptacle cover, which must be at least 15 years old. The cover just recently came off; it looks like the hinges failed or warped. To my surprise, this identical cover is still being made, though now it's called "Sigma Electric". When I googled GamPak, Sigma Electric came up, and the cover appears identical, down to the lettering on the front.

However, I have heard that these weatherproof covers are fine as "grandfathered" in, but if they have to be replaced, they should be replaced by an in-use weatherproof cover.

My questions are:

- can I just replace the old GamPak with an identical weatherproof one (but not an "in-use" weatherproof), or is it true that I must replace with one that is in-use weatherproof?

- if I have to replace with an in-use cover, can someone recommend one to me? Here is one I saw on Amazon: Red Dot (Thomas & Betts) CKMU While-in-Use Cover Is that a good one, or should I get a different one?

- is this a job for an electrician? I am not handy--that is for sure--though I think I could do just the replacement GamPak cover. But the in-use replacement cover looks more than I can do.

Current cover:

In-use Cover:

Comments (6)

  • 10 years ago

    The Red Dot cover is a decent product. You shouldn't be intimidated about installing a newer, code-approved receptacle cover...it mainly just involves a couple of screws. Click on the installation sheet pdf in the link below the photo and you'll see. It involves 6 steps, of which two are turning the power off and then back on, and one to caulk after it's installed! If you have a screwdriver, you're ready:
    Red Dot Cover



    User thanked kudzu9
  • 10 years ago

    I replace non-inuse covers with inuse all the time. Occasionally you might find some interference with the larger cover and the siding (in which case just put the old one back until you figure out what to do: a different cover or cutting the siding or extending the box).

    Note that the covers generally include a gasket that will seal the box fine. The caulk is necessary to seal up the opening to the house (not the box). Installations that rely on caulk to seal the plate the the box usually are problematic (don't get me started).

    User thanked Ron Natalie
  • 10 years ago
    last modified: 10 years ago

    Thanks everyone!

    Weedmeister - this patio outlet is used almost exclusively in dry conditions in summer and fall, and rarely at that (for leaf blower, radio mostly). Yes, it does just have 2 screws to hold it in place, though it's on a brick wall, and very well caulked. I am almost more concerned about being able to remove the caulk, and then re-caulk the new one properly. How do I remove the old caulk? It looks very solid.

    Kudzu9 - thanks so much for that installation sheet, much appreciated.

    Ron Natalie - the caulk on the existing broken cover is exclusively to seal the box to the brick wall. What kind of caulk do I need to buy for the new one? I will probably ask the helpful guy at Ace (local store is still old-fashioned enough to have people who will advise you).

  • 10 years ago

    sahmmy-

    To remove caulk, take a boxcutter or utility knife and cut through it all around the edge on all sides. Then, after you have the old cover off the wall, you can cut and scrape a bit more to remove the residue from the brick. For caulking, almost any outdoor caulk will work:

    Choosing caulk

    Latex-based or siliconized latex caulks are typically paintable, while pure silicone is not.

    And I suspect this might help, too:

    How to use a caulk gun

    User thanked kudzu9
  • 10 years ago

    I use a silicone caulk. If you will need to paint it to match use a paintalble caulk, otherwise I use white/clear as appropriate.

    User thanked Ron Natalie