Software
Houzz Logo Print
thaasjr

radiant heat questions

10 years ago

Hi all. I am building a 2200 sq ft home that I would like to have radiant heat in. I am planning on installing this in all of the lower level (concrete slab) and upper level garage. I am considering 3 zones.

I am my own contractor and building this with the help of my father and uncle. My uncle is a licensed plumber and electrician but has no experience with radiant systems. He would feel more comfortable if we got someone who's installed these systems before to help with the hook up.

My question is, how difficult is it to install the radiant lines throughout the home and get everything plumbed back to the manifolds? Basically everything that would need to be done to pour my slabs. Once we get the house sealed up I can find someone to help us bring the system to life.

Do I need to know exactly what I am doing for a boiler/water heater/ heat pumps etc before I install the in slab portion of the system?

I have considered using an online store for the in slab supplies and design layout. Does anyone have any experience with Blueridgecompany? I spoke with them on the phone and they seem pretty knowledgeable. My friend has used their pex with good results. I believe it would be 1/2 in O2 barrier line in 1000 ft rolls. Substantially cheaper than my local stores. Is all pex of good quality?

Thanks for any tips and insights.

Comments (5)

  • 10 years ago
    last modified: 10 years ago

    "My question is, how difficult is it to install the radiant lines
    throughout the home and get everything plumbed back to the manifolds?"

    Well, they managed to do it tens of thousands of times in the 50s and 60s...without the aid of our "modern technology".

    Sorry your thread died, but I just thought I'd bump it and chime in to say you absolutely right to go with radiant slab. I had it in my house for a few years before switching to "scorched air" and sorely miss it. In retrospect I should have kept using it. Few people know about it but if you can afford it, you should absolutely have it. It's still out there, I know an very wealthy couple who just installed it on a vacation house in the Finger Lakes. But a lot of people who think they know all about luxury house fixtures/appointments haven't heard of it.

  • 10 years ago

    What are you doing for air conditioning? If you are going to run duct work and you want a comfortable and quiet heating system then did you consider a modulating variable speed furnace?

  • 10 years ago

    “How difficult is it to install the radiant lines throughout
    the home and get everything plumbed back to the manifolds?”

    “Do I need to know exactly what I am doing for a
    boiler/water heater/ heat pumps etc. before I install the in slab portion of
    the system?”

    “Thanks for any tips and
    insights.”

    No, it may not be difficult
    to install in-floor radiant and work backwards and around whatever problems
    arise ‘to get some sort of heat going’ -
    but I would advise against it.

    There are just too may
    variables to getting an efficient, well-designed system going. If you’re asking
    these questions then I would surmise that you don’t even know all the
    right questions to ask when sitting down to design a well matched, well integrated, efficient, sensible system from front to back.

    This is something you would want get right – the first time out! You wouldn’t want to be working with people
    that know almost everything about
    radiant.

    There's a lot to know;
    there is a lot to know about what you don’t know. You wouldn’t want to find out
    ‘as you go’ - that might be very costly!

    Hire the right
    professionals; it might be cheaper in the end.

    IMPO

    SR

  • 10 years ago

    You need heat transfer calculations and you need to calculate how much emitter (pipe in your slabs) is needed to transfer that amount of heat at the temperature that you want to run your boiler. Ideally, you want to run your efficient, modern boiler at condensing temperature most of the time. That means that the return water temp should be 130 F or lower.

    There are lots of boiler/hydronic heat gurus at Terrylove.com heatinghelp.com

  • 10 years ago
    last modified: 10 years ago

    While this thread is up...

    I've heard through the grapevine of a system in a Baltimore home that was installed in the 1940s and is still working. Anyone know of one older still in use? Mine is a little younger, but in my case I was worried about the pipes someday leaking. It needed a new boiler a few years ago. But there was no evidence they were leaking and it might have been worth the risk to keep using them. It's such a comfortable, quiet form of heat in the winter. (my utility room is under the slab so you hardly hear the boiler)

    Also I was swayed by my plumber, who was very, very good on previous work (only local member of the building trades I've thought was good and honest) and would have been licensed in MD to do a boiler replacement, but he said he just wasn't willing to take on the job because he thought it could be fraught with difficulties. He thought that the bleed valves were rusted over and it would impossible to get air out of the system...and therefore the best way to do it would be to freeze the main boiler input/return pipes to form a water block. (the original system installer didn't provide a way to isolate the boiler loop) But my oil delivery guy said his company did lots of boiler replacements and never had trouble getting air out of the lines...eventually...so...oh well. If the super honest plumber had been willing to do it, I probably would have done it. Went with Carrier HP + propane backup, and I'm warm enough in winter but think the reliability of the brand is overrated.