Software
Houzz Logo Print
texguy82

Ceiling Wiring Not Working with Fan and Remote

10 years ago

Purchased a Home Decorators fan to replace 3 older fans in house. There are 2 switches at the wall plate and wires from ceiling are white, black, and bare copper.

Original fan wiring went as follows; black from fan to white from ceiling, blue from fan to black from ceiling, and white from fan to bare copper.

Following the directions on new fan wired it as follows; black from fan to black remote receiver, blue from fan to blue remote receiver, white from fan to white remote receiver, green from ball and mounting brace to bare copper, black from remote receiver to black from ceiling and white from remote receiver to white from ceiling. Neither fan nor light worked. Tried swapping the black and white wires from ceiling and remote and still didn't work.

I am stuck on how to get these fans working with this remote. If I take the remote out of the equation and hook the fan up directly to ceiling wires (same way as the old fan) both light and fan will work, I just can't dim or change fan speeds.


Comments (6)

  • 10 years ago

    You say that there separate wires from the wall switch box to the fan. Why don't you just get a wall-mounted fan control and skip the remote. I got a Lowes-brand fan which I can only control with the remote, which I hate. For my next fan(s), I am going to make sure they can be controlled from the wall switch (my builder ran two lines from the wall switch to the fan box in each room where I plan to have a fan).

  • 10 years ago

    The only wires coming from ceiling are 1 white wire, 1 black wire, and 1 ground, so I am not sure exactly how they terminate at the wall switch. I will have to check that out. Reading around I've seen there should be an additional red wire since there are 2 switches? No clue really about that. On the old unit 1 switch worked the light and 1 switch worked the fan though.

    I'm really hoping to not have to spend an additional $20+ per room on fan/light control switches to get these working right (the switch style I do like is $35). I can live with using the remote if I can get it operational.

  • 10 years ago

    Someone used the white wire in a way that was not to code. What is worse, is that they were using the bare copper wire for the neutral. You need to open up the switch box and fix the mess that they created in there. I am guessing it is a single gang box with a stacked/ double switch, or at least the two controls for the light and fan are in a single unit. I would hate to think that someone would have gone to the trouble of switching to a two gang box without also putting in the correct cable.

    You need to take the white wire off of the switch and connect it back in with the rest of the neutral wires in order to wire the fan the way you tried to do it, which is the correct way. You can put the black wire to the light on a regular single pole switch. It will then turn the fan and light on and off at the same time, but you will need to use the remote to control the functions separately. The switch will have to be in the "on" position for the remote to work. You could just put a blank plate at the wall switch, but it is against code to not have at least one wall switch operated outlet in the room.

  • 10 years ago

    The remote controlled fans can only be controlled through the remotes AFAIK. As Fred S states, a switch will turn the whole thing (fan and light) on or off, but to adjust speed you'll need to use the remote. You need a pull-chain type of fan to operate both independently with the wall controls.

  • 10 years ago

    Yes it is a single gang box with stacked switches.

    I believe I understand correctly that this will change it from 2 switches to 1 switch only in order to have the fan operate correctly with the remote. That 1 switch will then turn on both the light and the fan together.

    I came across an older post on a different forum where somebody made a comment they had this same model fan and were able to wire it with the remote, but keep it on 2 switches with the fan being controlled by one and light by the other. Am I correct to assume that cannot be done with my current wire setup? Would it need to be rewired to include a red wire to do this? I think I am fine having it just be on 1 switch so it can be turned on/off as people enter/exit the room and then just change the settings with the remote.

    Thank you for the help.

  • 10 years ago

    It sounds like you have got it straight.

    As far as how the remote operates with a switch 'exactly', I couldn't be sure because there are several different ones out there, and I have rarely wired any of them. I do almost all new construction, and put in the right wire and enough switches to steer people away from the remotes that you can never find when you need them. I hear that some reset when the switch is turned off at the wall so that at least the light will come on when the switch is turned back on even if the remote had the light off...which would be a good thing.