Software
Houzz Logo Print
ewalley

to schluter or not

9 years ago
I have hex shaped marble tile..one pro says I need a schluter,several said I do not..a silver strip takes away from the beautiful tile.. I am adding a floating shelf to have an end place to stop the backsplash.. I want 2 shelves..2nd one staggered and ends at counter edge.. first one only goes to the end of where sink ends.. 28 inches... should I use a brass schluter to match hardware or marble has a straight edge as is.. where do I stop the marble..edge of counter or where bottom shelf ends.. the tile guy is not finished.. .. brass schluter I found online or on houzz..

Comments (21)

  • 9 years ago

    Need to see the edge in question -- not understanding the geometry of the elements involved AT ALL. If this hex tile somehow has a straight edge, then there's no need for Schluter...

  • 9 years ago
    I get that confused look a lot.. if hex is fit together like puzzle at edge of counter,it would be a straight edge cut, trim would only need to be accross window where no top point to stop...theres a twin window opposite the vent hood not seen.. ..backsplash will end at counters edge or where top floating shelf ends..(not hung yet)or where the bottom floating shelf ends as shown.. the tape is where the bottom shelf will be... iy is not tiled up to the point yet.. ..
  • 9 years ago

    I think a small, brass edging would fit nicely w/you modern elements. Is the shelf going right on top of it? what about where it ends at the edge of counter? a strip or something is needed there.

  • 9 years ago
    I wouldn't use brass, which would call attention to itself. I'd use a thin edge in a pale neutral gray. Or anodized. There are some straight-edge, minimal Schluter products available, but most colors are available by factory order only. You might be able to use a good matte spray paint on it if you find a profile you like, especially since it sounds like it will be a small area.
  • 9 years ago
    I think the brass/gold trim would work great with your pendants
  • 9 years ago
    the first shelf,I envision, is on the tape,ends about where sink ends.. 2nd shelf is staggered above it and goes to end of counter.. do I have to carry the tile to end of counter,and therefore include tile up to the bottom of the top shelf.. very very pricey tile.. I have another 10sq ft I over ordered.. but I don't think that is enough.. my hardware I'm trying to match color with the schluter..my inspiration shelving but only 2.. not the middle one..just staggered.. I also don't want the bottom one to end of counter..my kitchen had a cabinet over it and I tore it out..I'd hate to our a floating shelf there..I'd thought would defer the purpose of opening up kitchen.. if u sit at counter with barstool or stand there,you'll feel like you need to duck..
  • 9 years ago
    ooh,my custom pendants are on way..they have same brushed antique finsh as hardware..they are same shape as pictures but even more sleek..milk glass globes though..can't wait to hang.. these are nice..but just bought until I could afford the upgrade...
  • PRO
    9 years ago

    Typically, Schluter trim is the last resort, it would be nice to incorporate a marble pencil that matches or compliments the backs-plash to finish it out. If this isn't an option, it may be best to paint the Schluter trim to match the marble as closely as possible so it doesn't stand out.

  • 9 years ago
    it is paint able?and won't chip over years??grout line I'd think, if done well, will be all that is needed..of course with the crew my contractor hired,I can't count on that..
  • 9 years ago
    where do I end the backsplash? I'm up for any combination of floating shelves..
  • PRO
    9 years ago

    I have learned never to accent something that you want to hide. Why make the unwanted trim stand out? I am sure a designer can make it work in a picture but in real life there is no way I would do it.

    You could buy a bullnose wheel if you have a grinder and roll the edge over.

    I would go to Home Depot and buy their $10.00 plastic 1/16 thick and about 3/8 visible from the top. It cuts with a nice which makes mitering and a flush fit easier.

    Once you grout it will blend right in. The larger profile moldings will stick out and be visible. Did one on the shower of my own bath and wish I never did. It looks like a stick on brushed silver i don't know what. In other words it draws your attention to it and that is not want you want.


    Good luck

  • PRO
    9 years ago

    It could be done a few ways:

    one way would to be to butt the tile under a floating shelf that aligns with the bottom of the right most cabinet. Another way would be to tile the entire opens space to the right of the right most cabinet all the way up and to have the tile behind all of the floating shelves. In either case, Schluter is not needed.

  • PRO
    9 years ago

    Also, you might consider deleting the floor register and find a way to diffuse the air via the toe kick. Also consider plug molding for electrical outlets beneath the upper cabinets versus outlets in the back-splash.

  • 9 years ago
    too late for electrical..in hindsight would been best.. but already have completed most of the floor and most of the backsplash..I tried to do a little upgrade to electrical but contractor said no wiggle room in the budget .would require moving a junction box or something like that.. 1960 kitchen. I was just planning update color of cabinets and add new counters,floors,backsplash ..
  • 9 years ago
    no more tape,and no tape measure.. can I stop wherever first shelf stops?even if up higher like pic one??or must I put floating shelf at base of farthest cabinet as in 2.. ..and what space between??15x18"??for pucher,glassware, or click or art..
  • 8 years ago
    Hi if I have a satin nickel finish schluter what paint would I need to use to paint it white? What type of prepping? Should I seal it afterwards in something? It’s in a shower. Thank you!
  • 8 years ago

    David, you don't paint the Schluter. if you want white, then get it in white. they come in various colors. otherwise, leave it nickel.

  • PRO
    6 years ago
    last modified: 6 years ago

    I would not highlight a functional detail like the schulter strip. Feels very heavy-handed, design wise.

    I would take the tile to the counter's edge, along with your shelves.


    Or take the tile to the counter's edge, ditch the shelves altogether and hang two stacked pieces of art with a thin brass frame.

  • 6 years ago

    wish i had the money.the contractor did horrendous job.never completed.got attorney and he still never finished. but of course i paid,so my bad.i see its been 3 years and i still go into my kitchen with remorse.im at work during the covid-19 virus so i cant send pics.(blessed to be working) but the cabinets are cheap,painting horrible threshold not match wood floor,tilework crooked,cabinets not alligned. stuff he said he would fix at the end.list goes on.

  • PRO
    6 years ago

    Oh my gosh, I just realized this post was from 3 years ago....

    Oh wow, that's a terrible twist to your project. Ugh, so sorry to hear that! It's always so hard when you invest your hard earned money into a project that "professionals" take for granted (hard emphasis on quotations).

Sponsored
AIS Renovations
Average rating: 4.5 out of 5 stars15 Reviews
Custom Craftsmanship & Construction Solutions in Franklin County, Ohio