Software
Houzz Logo Print
maestrope

New Marvin Elevate inserts a bit hard to open: advice?

4 years ago
last modified: 4 years ago

I just replaced 80-year-old windows with new Marvin Elevate double-hung insert/pocket windows and they are a bit hard to open -- not terribly hard, but a bit more than I expected. I'd like to ask for advice.


Context: My installer and I discussed the process extensively. Based on recommendations from this forum, we installed from the outside, added minimally expanding foam (the type for windows and doors) inside the cavities for added insulation, and flashed all the sills for added precaution. The measures were taken with digital measuring instruments to the 32th of an inch (in three parts, always selecting the smallest measures), and the sill angles computed with digital angle finders -- obviously, Marvin subsequently did the relevant deductions from opening size to frame size. To minimize loss of glass area, the units fit right, not too tight but certajntly not too loose. The existing 80+ year old frames were in good conditions, although some were a tiny bit out of square (but, again, I took measures in three parts and selected the smallest). We checked that the units were plumb, level, and square, with a 4 foot level and with a digital angle finder. For some of them, we checked with a laser level for horizontal and vertical. We used a minimal amount of shims (as mentioned above, the units were measured as to maximize glass area). We also shimed so that there would not be daylight visible in the vertical sides of the sashes as seen from the inside. We have not installed the outside trim, so we still can make adjustments.


I am at a bit of a loss why they are a bit hard to open. (They were easier to slide up and down when you could see daylight from the inside, but that would not be a correct install, hence the related shimming.) My installer and I will again check for plumb, level, and square, and will use the digital level to check horizontal and vertical for all of them. I am planning to also use dry lubricant especially made for windows to lubricate the tracks.



Is there anything else that I am missing?

Thanks.

Comments (8)

  • 4 years ago

    @maestrope My initial though is you may pinched them with the shims, especially since you stated that they operated easier prior tot he shims.

    maestrope thanked millworkman
  • 4 years ago
    last modified: 4 years ago

    Thanks, @millworkman. I also thought the shims were the issue. However, I only used shims for two reasons: 1) to ensure the windows were plumb, level and square, and 2) to ensure there was no daylight at the side of the sashes when looking at them from the inside. My understanding is that we have to ensure both #1 and #2 -- it would be unacceptable to not have the window plumb/level/square, or leave the sashes so "loose" that one could see daylight. We used black plastic stackable 1/16" shims around the per pre-drilled screw holes, and it was mostly only 1 to 2 shims per hole -- in rare occasions, three shims, and some of the holes needed zero shims. The reason we actually used fewer shims than expected is that the windows were measured very precisely. Marvin Elevate frames are 3/8 shorter than the opening width, or 3/16 in each side, less than the usual 1/4 per side. But I did follow the instructions, and measured precisely -- perhaps too precisely -- and let Marvin deduct what needed to be deducted.


    1) I will use the dry lubricant. It can only help. Any views on that?


    2) We have not installed the trim yet. Should we remove some of the shims, risking that some windows would no longer be plumb/level, or risking some daylight from the inside? Also, we put some minimally expanding foam for windows and backer rod, so removing shims might mess up the foam at this point...


    3) Instead of removing some shims, should we slightly loosen some of the screws?

    3) I was actually at a Home Depot earlier today and tried some of the windows they have on display. There were clearly easier to operate. Should I assume that any window that is a floor sample, and not installed/shimmed in an actual construction site, would always be easier to operate? I'm just trying to get some perspective...

  • 4 years ago

    Experiment a bit before using the lubricant. Back the screws out a hair, you can actually tighten them again if needed. Although loosening the shims may not have the effect you are looking for, maybe pop a shim out of each side.

    maestrope thanked millworkman
  • PRO
    4 years ago

    Take a look at the weatherstripping gaps.


    These Marvin threads tend to get a bunch of posts...hmm

    maestrope thanked Windows on Washington Ltd
  • 4 years ago
    last modified: 4 years ago

    Thanks, @Windows on Washington Ltd. The weatherstripping looks fine, and we closed gaps (with shims) such that there is no visible daylight from the inside, as I understand should be the case.

    The windows we have begun to re-check today are indeed plumb, level, and square, without excessive shimming, and with no daylight visible. Lubricant seems to help, and I will put some in all windows. I will also assume that time and use will "break in" the windows.


    To be fair, opening them is an easy two-hand operation, but not an easy one-hand operation, and certainly not a one-finger operation. Perhaps I have been conditioned by some commercials vouching windows (usually vinyl) to be a one-finger operation, or by big box floor samples (uninstalled units) that are very easy to open. Is it fair to assume that a tight but perfectly operable (with two hands and reasonable effort) window is much better than a loose (and less energy efficient) window? Do new windows "break in" with time and use? And, are Marvin Elevate known to be tight to open?

  • 4 years ago

    Thanks, @millworkman. My apologies: I am not using my adjectives very well today. I should have said: they are a "not-too-easy but not-too-hard" two-hand operation. They are a rather hard one-hand operation, and an extremely hard (if not impossible) one-finger operation. Since they are plumb, level, and square, and do not appear to be over-shimmed, I will need to conclude that they will break in with time and with some dry lubricant especially made for windows. I guess "tight and not extremely easy to open" is better than "very easy to open and thus potentially too loose" in terms of energy efficiency. Thanks again.

  • PRO
    4 years ago

    Well...they will never be as "tight" as when they are new. The pile or compression of the weatherstripping is under the most tension when they are new.

    maestrope thanked Windows on Washington Ltd