Software
Houzz Logo Print
shirleyannen

Mis-aligned crown moulding

3 years ago

Hello All -


We are undergoing a kitchen remodel and had custom cabinets made to replace builder-grade cabinets and pantry. The new cabinets are not flush with the wall edges, which has resulted in the crown moulding being mis-aligned (please see red circled areas in 2nd photo). I don’t think this is acceptable, especially for custom cabinets, but would appreciate any input. Thank you in advance.


Old pantry:



New pantry:


Comments (15)

  • 3 years ago

    I think, once its painted, it will probably look better, but, no, I dont like it. I am not so sure, I would want any crown in that area, since its so narrow.

    shirleyannen thanked cat_ky
  • PRO
    3 years ago

    Cabinets should never be pushed so close to the edge of a wall. You want them a minimum of the crown extension plus an inch from the wall end. That’s a design issue. The low quality of the cabinets is a build issue. Custom is not a synonym for quality.

    shirleyannen thanked Lomo
  • 3 years ago
    last modified: 3 years ago

    I’m not clear on what or why you think the crown is misaligned in those 3 spots. How else would you have the continuous crown bridge the gap of the uneven surfaces between cabinet ends & wall protrusions? It would look really odd to have stops / starts with bare wall in between. The only other option for the space in spot next to stairs - on left in pic - would be to stop that crown run on the cabinet end next to wall. With that, the crown end on the cabinet would look just like the crown end on the small wall end section. Not good. What was done is IMO the best. Move on, paint & enjoy your lovely new storage!


    ETA - I also think the cabinets ending design are not low build quality - it’s a communication issue that the cab builder didn’t explain the cab ends shouldn’t be flush with the walls. That failure to communicate led to unrealistic expectations and your disappointment.

    shirleyannen thanked KW PNW Z8
  • PRO
    3 years ago

    Crown molding needs room to die into the wall. Cabinets need to be less wide and less deep than the walls to which they are attached. The cabinets are too large, and do not allow that to happen. Or, the wall isn’t deep enough/long enough. Take your pick. But the walls were there first.


    Not a fan of the jointed crown, or finishing in the field either. That usually means other shortcuts have been made. Which the crown install and cabinet sizing confirms. This is not well done as a whole.

    shirleyannen thanked Quicklok Cabinets
  • 3 years ago

    Your cabinets sizing is off; leaving what looks to be about 1/2” or so from the end of the cabinet to the the end of the sheetrock corner. Because of this, you crown molding had to accommodate it. I think your cabinets were not measured correctly. My kitchen crown molding looks alot more appealing; as the cabinetry was measured correctly.

    shirleyannen thanked kculbers
  • 3 years ago
    last modified: 3 years ago

    Continuous crown doesn’t die into the wall. Pictures that show crown on cabinets only are great but that just doesn’t work for continuous crown.

    What the OP has will look fine when painted. If you have any experience with crown in old homes you see this around small bump-outs all the time.

    shirleyannen thanked bry911
  • 3 years ago

    I agree totally with @bry911 The finished result will be fine & no one but OP will notice OP’s issue with crown endings. We have heat vents high on wall close to ceiling and when we had crown installed it overlapped width from ceiling to heat vent - which couldn’t be moved even slightly. The person who installed our crown did exactly what was done to bumpouts in OP’s situation - ours is just a bit less of bump. But, no one notices & if they do, it’s to praise the skill of the crown installer to have done such a nice job with that situation! So, as I said before here, what was done is the best, move on, paint, enjoy the great new cabinets. Nothing to be fixed or further point out ’should have done’……

    shirleyannen thanked KW PNW Z8
  • 3 years ago

    It'll look good, and less squirrely than what you had before, believe it or not.

    shirleyannen thanked Fori
  • 3 years ago

    It looks fine. Whoever did the crown knew what they were doing. There is a wee amount of space between the cabinets and wall, so the crown cannot be flush.

    shirleyannen thanked shirlpp
  • PRO
    3 years ago

    Like others, once painted, it will blend in and no one will notice.

    When I was doing custom cabinets, I sometimes added a molding to the cabinet to take up the space and make it look purposeful.




    shirleyannen thanked PPF.
  • PRO
    3 years ago

    One is crownon a wall the other crown on cabinets never the twain shall meet since the cabinets were made short of the wall space anoter piece added to the cabinet like above would have solved the issue When I use "custom" cabinets they better darn well be custom.

    shirleyannen thanked Patricia Colwell Consulting
  • PRO
    3 years ago

    The person who installed the crown did an excellent job considering the circumstances he was handed.

    shirleyannen thanked Joseph Corlett, LLC
  • 3 years ago
    last modified: 3 years ago

    Everyone has a personal preference, I grew up in a traditional colonial with higher ceilings and a nice crown that was uniform in the entire first floor (including the crown on the cabinets).

    If you have crown on one floor or area of your home, I prefer it be carried throughout the entire house (or at least all the connected public spaces), I think it is silly when you have a traditional painted kitchen and the crown suddenly stops in that room everywhere but above the cabinets.

    shirleyannen thanked bry911
  • 3 years ago

    The cabinets stop short of the wall for a very good reason. Because walls are never perfectly plumb. If you tried to end cabinets flush with a perpendicular wall, you would have bits of cabinet overhanging part of the wall and part of the wall showing in other places and a bit of cabinet flush. So you would be seeing just how out of plumb that the walls are and never give the crown molding a second look.

    The installer did a very good job with the crown install. You should be thanking him and not nitpicking over the impossible.