First let me say that I do not own an in-floor system. However, the reason I am responding is because I have attempted to help many people with in-floor systems who were trying to reduce their energy costs. The problem with nearly all in-floor systems is that they require high pressure and flow rates to work properly and both of which require large pumps that use a lots of energy. So not only are in-floor systems expensive to install but they are also expensive to run. Some people care, other don't but I just like to make people aware of this aspect in case they do care about having an energy efficient swimming pool.

Womanowned,

We put in a handfull of A&A infloor systems in the mid 90s and I maintain contact with 2 of those customers at present and they are happy. They were lower pressure systems with acrylic balls that floated around in the distrubuter valve to change zones. Both customers have had to rebuild the gear mechanisms and replace the heads.

In 99 we switched to caretaker because the equipment was under the pool and the A&A system wouldn't work under those conditions. We have done about 10 caretaker systems since then and rebuilt the valves and replaced the heads on three of those. Caretaker has a really good lifetime warranty program for parts.

I have personally laid out every infloor system we have done and wouldn't trust that to someone unless they had a lot of experience. Its a pain because it really slows down the job progress. We have never charged enough to make a profit if you factor in everything. Texas might be different because you have so many subs and there might be a plumbing sub you could trust it to. We do our plumbing in house so its like building a prototype for the 10th time.

Most of our customers are happy with a polaris.

womanowned....we're in Louisiana and have had our Paramount PV3 system since 2007..absolutely no problems with heads or the distrubutor valve.

That being said, we have it matched with a 2 speed pump and the floor cleaning heads and distrubutor valve only see 1.5 hours of high speed operation per day...the rest of their duty is at low speed which does a surprisingly good job of cleaning throughout the day.

Most of our debris is leaves, so that may make a big difference on effectiveness of the floor system.

From talking with Paramount, they said leaves are the easiest to clean and sand is the hardest.

Agree with renovxpt....follow the engineered drawings provided by the floor system manufacturer. I checked and double checked the head position to the print before gunite and had the plumber make adjustments accordingly.

For efficiency conscious customers, place the distributor valve as close as possible to pool and run large pipe to it from the pump. After the distributor, only 2 inch pipe can be used, so the shorter the runs after the valve, the better.

Thanks everybody for your feedback. Good stuff!

I also encourage not using flex PVC anywhere. Floor systems tend to have some significant pressure in the pipe that causes flex to expand and contract.

Most concrete pools have gravel under them. The expanding and contracting will cause an impingement. I've seen it too many times.

Most floor systems have several heads per zone. Finding the one that leaks now gets that much harder to find and fix. Using hard pipe will go a BIG way towards preventing this from happening.

Scott

I have an almost 3 year old PV3 system. I run the system 2 hours a day 3 days a week. For the few weeks a year when leaves are falling heavily, I run it 2 hours a day 7 days a week. I have it hooked up to it's own single speed pump.

trhought, I'm interested in how your system performs at low speed on your 2 speed pump? Do you use this mode more for just better circulation?

I get a small amount of dirt year round and leaves in the fall and winter. The leaves are handled within a few days very well by the PV3 system. The dirt is mostly cleaned up but I usually accumulate some dirt in one section of the pool that I have to manually vacuum every 2 months or so. It's hard to see though with my wetedge primera stone black kona finish.

The system itself has operated well. The pause/run selector on the port has developed a minor leak and the pressure gauge has moisture inside it and needs a gentle tap to get it to read properly. I've had two caps on the heads that have cracked and kept popping off but my pool builder generously gave me the tool to remove the heads and plenty of extra caps to fix that problem.

My wife was adamant about avoiding the creepy crawly cleaners and so that combined with the mostly successful performance of this PV3 installation was a win for me.

We do in-floor systems on almost every pool...we are a vinyl builder and we use the Vanquish system from Paramount. We have been installing them for roughly 10 years and while we have replaced a couple gear boxes issues are minimal.

It takes planning and good plumbing skills to get these to work perfectly.

We use all rigid 2" pvc with NO 90 degree elbows....only 45's.

We also now use Pentair intelliflo variable speed pumps on all pools and even in lower rpm settings it moves debris very well. WE program 1-2 1hour cleaning cycles on high speed and the system cranks.

So as far as energy consumption with variable speed pumps and correct plumbing I do not see an issue.

Also if you have a heater it helps heat the pool from teh bottom up thus heating the water more efficiently.

-Jay

Sorry for the ignorance -- do the in-floor cleaning systems really help with leaves and such? We got 2 different answers from 2 different PBs if it would help us. Looking at a chlorine pool 18x34 in an older neighborhood with quite a few mature trees nearby. One PB likes the Paramount cleaning system. DH thinks the designer must get a huge commission for selling it as it has been mentioned several times. So, of course, he thinks they are just trying to "up sell". Another PB said it wouldn't help us that much.

Just found these statements on the Paramount site. Are these really valid statements or glamourous marketing fluff??

1) PCC2000 is a systematic approach to permanent pool cleaning and circulation that will save you time and money through reduced chemical and heating costs.

2) Reduces Your Maintenance Costs! Your pools environment will have a large impact on maintenance costs, and the PCC2000 can really make a difference.

3) Paramount's PCC2000 enhances your pool invisibly, it keeps your backyard pool clean, automatically without your time and labor.

In a house we sold last year we had a Paramount in-floor (I believe it was a PCC2000) cleaner installed in a new pool by a very reputable builder in 1998. The first 5 years I thought it was the best thing ever. PB said it needed to be run 10 hrs a day to clean properly, and that is what I did for quite some time. Later on I got more concerned about the energy usage and the pump - never could get below about 6 hrs per day and keep things clean.

Each of what I call the "sequencer" units last about 3 years. Our system had 2 and replacement cost is $267 each. Figure $600 every 3--4 years to replace.

The heads are moving parts, and they wear out after 8-10+ years. There is a lifetime warranty on the part, not the labor. So you still need to pay someone to come out every time heads fail. Even though the heads all really need replacing they still only want to replace the ones that flat don't work. They usually "clean" other heads which work for 2-6 weeks and need "cleaning" again. The heads are pvc(?) and gradually wear out. To work, each head must settle down after it gets it's sequence and in the process make a 1/4 turn. It really got to be a drag messing with heads and the warranty process.

As far as the energy costs - I had to run the in-floor quite a bit to get things clean, even 98% clean. 98% sounds very clean but in reality when the walls are included it is a big spot that never gets clean. My neighbor with his Polaris 280 always had a spotless pool and seemed to barely run the cleaner. I give it thumbs down on energy.

Chlorine and heat distribution - this is where the in-floor really shines, A+.

No hoses or equipment in the pool - this is also a plus with in-floor.

Overall based on my experience the initial cost, additional energy cost, and similar if not inferior cleaning of the in-floor are not worth it.

If anyone asked me in the first five years of ownership about the in-floor I said it was the best thing ever. Now, I'm not sold on the benefits. If I did get an in-floor cleaner I sure would have my pool plumbed for a pressure-side cleaner as a backup.

Do not go with Pul Products

theyve no idea what they are doing

they have a great ad but thats it

ive had water in my pool for over 5 months and their in floor filtration system is still not working

what a joke! they have no idea how to make it work all theyve done is throw parts at my pool builder expecting him to figure it out

stay far away from this company

I use the Caretaker system but not in the way a traditional system is used. I don't use the any collection system but just the heads in pre-determined locations. Mostly for steps, benches and sun shelves. A pressure side cleaner does the dirty work

Jandy will provide a detailed diagram for dealers for head locations if provided a pool plan.

Following the plan exactly is very important to proper function.

I've had great success using this product.

First of all, by logic, moving the water thru an in floor cleaning system is way better than moving it thru normal wall returns. I own an infloor cleaning system from more then 15 years, and it worth it. My cleaning system works with the filtration, so it is the same pump who run both. Pump is powerful than a simply filtration pump, but it runs less time/day. The cleaning nozzles rotate about 12-15° each time they pop up, (about each 6 minutes), so it takes approx. minimum of 3 hours of working hours to clean 360°. No problems at all in all those years. If you compare it with a vacuum cleaner, is a waste of time. First of all, a vacuum cleaner has to be used as often as the dirt is coming into the pool. Someone has to do it, and works similar to a home vacuum cleaner…Second problem is the vacuum cleaners are not free, and brokes very often. Just go into a swimming pool shop and first think you will see are full shelves with vacuum cleaner replacement parts…Seems like the concept of the inkjet printers. You buy a cheap printer, but then you replace ink cartridges like crazy, as they empty by just calibrate the injectors…

My personal opinion is, a pool without an infloor cleaning system is a waste of money and time. What it is true, that you need a very good installer, and this is really the hard part.