Software
Houzz Logo Print
jmbaker3_gw

Need help locating Cedar Posts

18 years ago

Need to find 4 x 6 , 12 ft. Cedar posts for my deck. The deck was built in 1989 and a number of the posts, which were clear cedar... have rotted at the bottom where they were in the ground. Anyway, I have been jacking the deck and cutting out the rot, then placing the post back down on pavers, which have been built up from the poured footing. Well... I am done with this half a-- approach and am willing to break down and replace the posts. Looking at around 14 posts. Will accept knotty with a tight knot pattern. I have explored all the pressure treated possiblities and just want to put cedar back in... I know it is expensive today and has been hard to find. Need vendors in my area if any one knows... Washington, DC... Annapolis, Md. area. Thanks.

Comments (13)

  • 18 years ago

    Clear Cedar posts are going to be scarce and expensive where you're at, I would think. Another option that might work would be to install pressure treated posts and wrap them with 1x clear cedar.

    Mac

  • 18 years ago

    If you are going to go back with cedar post make sure you use post base this time instead of burying them into the concrete or you'll be doing the same thing all over again.

    Where to buy cedar post? Get out your yellow pages, look up lumber companies & make a few calls. Ask for rough sawn cedar 4x6x12's, they should be able to help. Don't even bother calling Home Cheapo or Blowes.

    Al

  • 18 years ago

    Yes, the posts have been difficult to locate and I can get them thru American Cedar, buying a tight knot post... the cost is $98.00 each... existing posts are clear and have been in since 1989. The footings are about 13 inches below grade and were never brought to the surface, so the posts were "in ground", covered by mulch, which lends itself to decay overtime. I have looked at 4 X 6, 12' pressure treated, but they tend to bow, badly... I could go 6 X 6, but at this time just way too much work to do, then wrap, etc. I have been bracing the deck and cutting the rott out, then adding a post base and building the footer up to grade with paver type materials... but just don't feel too secure with a post on a deck this size just restng on a paver and not being locked in... I will most likely just order the cedar, bite the bullet and set them back into the ground... hopefully I can help with the aging process by maybe adding tar or some preservative to the area which is inground. I got close to 20 years out of the originals... maybe the next set will outlast me.

  • 18 years ago

    Quote by jmbaker3 - "but just don't feel too secure with a post on a deck this size just restng on a paver and not being locked in.."

    Yah, I'd have to agree with ya there. No way should that be the case. You should dig a hole, install a 12" diameter (min.) sonotube, pour a concrete footing w/ rebar, install a Simpson CBSQ post base in the wet concrete ,
    and let the concrete set up for a week or two

    THEN install your 4x6 post on the post base. This will keep the bottom of the post out of the ground, away from mulch and generally much happier. Happy posts will last much longer...

    Regarding the twisting and bowing, not sure if you've got hem-fir or SYP pressure treated wood, but I know a lot of deck guys who build with both those materials with good results. Wrapping the post would further reduce the chance of bowing and twisting because the post would not be directly exposed to sunlight/weather.

    Mac

  • 18 years ago

    jmbaker,

    Biltbymac maybe right, I don't know. I have no idea know how much work that is.

    You could also just go with a stone backfill.

    I think most of the post rot is in the top several inches of soil. Don't backfill with dirt, and keep mulch away.

    Use 3/4" gravel to backfill, or use QuarryProcessed (QP). QP is gravel mixed with lime. When the QP gets wet, it sets up like weak concrete, but still drains water.

    Bottom line, do things to draw the water away from the posts.

    Also - I think fence guys recommend 2 coats of stain on what goes below ground. And if you want to nail some copper flashing around the posts at grade also good.

  • 18 years ago

    Tom, that copper thing is a good idea we use flat stock wraped around the posts 6'' or so below grade 6'' on top fastend with copper nails. Its an old Jap trick. I use this mostly for Arbors that have to have posts in the ground.

    However its much better to do what the Mac sugested far as the piers and conectors. John

  • 18 years ago

    It's not a question of how much work it is, you just build it right and build it to last. You don't want to have your deck collapse when it's loaded up with a graduation party or family reunion.
    Digging holes and pouring concrete footings -
    Is it more work? Yes
    Is it more expensive? Yes
    Is it going to last longer and make a safer deck than burying posts? Yes
    (The last question is the most important one)

    Mac

  • 18 years ago

    There are already footings in the ground, so no fear of them not being stable once planted back into the ground. I just did not want to build UPON the existing footing... I have located "clear" cedar 4 x 6 and have gotten a price of 11.75 a foot and they are available immediately... though all are much longer then I need... I think the price is good and it will match the existing posts which remain.

    Now I just need to research the best way to preserve the portion which will be buried in the ground on the footer...

    Will look into the copper wrapping option as well as using a preservative. I have gotten close to 20 years out of the ones in the ground now... another 20 years, and even I may not last that long.

  • 18 years ago

    To bad you don't live down in the Georgia area. 4x6 runs about $5.25/foot.

  • 18 years ago

    "To bad you don't live down in the Georgia area. 4x6 runs about $5.25/foot."

    Clear???

  • 18 years ago

    It's called appearance grade. They state that knot free is not available. Are you sure yours is clear?

  • 18 years ago

    Are you resting the posts on the existing buried footings or are you attaching them to the existing buried footings? Without a physical attachment to the buried footings, you have no protection from uplift or seismic activity.

    If you are going to bury your new posts, look into this product or one similar to it - http://www.postsaverusa.com/

    Mac

  • 18 years ago

    "Are you sure yours is clear?"

    Yes indeedy... I just saw them with my own eyes... should be here on Thursday. Will match what I have up now. I will have some nice stock left over, once cut... maybe I can find someone who is interested.