Software
Houzz Logo Print
dc_pilgrim

Cost for relocating the Electrical Panel

17 years ago

I am planning to finish a room in my basement, but the electrical panel in inconveniently located. It sits in a corner, I'd like to move it to the adjacent wall, about 2-3 feet into the room (under the pvc pipe).

Any sense of the cost associated with this? I understand location is a big factor - I am in PA, not in a metropolitan area. Are we thinking $500? $1000? $5000?

Here is a pic:

Comments (15)

  • 17 years ago

    I'd say a minimum of $1000-$1200.
    Any further into the house and you will need a main disconnect outside.

  • 17 years ago

    looks like most or all 12 & 14 romax is coming from that wall. service wire will need to be changed and pvc extened.
    $1000.00 to 1500.00 should do it. excluding drywall repair.

  • 17 years ago

    Thanks for the feedback. Not free, but not impossible. I REALLY wish builders would put all this stuff together (h/w heater, furnace, panel, sump, etc). Oh well, I guess one day when if we ever hire a custom builder.

  • 17 years ago

    "I REALLY wish builders would put all this stuff together (h/w heater, furnace, panel, sump, etc)."

    The NEC places vague limits on how far the meter feed can be run inside the structure.
    These lines only have protection from the line fuses on the primary side of the pole transformer against faults.
    The pole transformer can deliver huge amounts of current (think over 10,000 amps) if these lines are shorted to each other or the neutral.
    The main breaker in the panel protects them from overload, but only the high side fuses on the POCO wiring protect them from shorting.
    The further they run the further lightning induced transients are carried into the house also.

    At the very least rigid metal conduit may be required to run them any distance inside the structure, or a main disconnect with fuses outside the structure.

    The AHJ has the call on how far they will allow them to run inside the house.

  • 17 years ago

    Just out of curiousity, how would this be done? I can't see how it would be done without some sort of splicing.

  • 17 years ago

    Splicing is what I was talking about. To move the panel, you are going to end up with some of the circuit wiring being too short. The minute you start splicing, it has to be done in metal boxes that must be visible for access. Not quite sure why the OP thinks the panel would be less onerous around the corner from its present location.

    I can put up with a lot of ugly for $1,500!

  • 17 years ago

    No kidding. If it ends up being spliced in a visible box (what I'd assumed anyway) you may as well keep the breaker box where it is. Box it in/cover it up.

  • 17 years ago

    You may have a code issue regarding the pvc drain if it is not set off of the wall far enough. You can not install the panel under any obstruction like that. 2002 NEC requires dedicated space below the panel to the floor and above the panel for 6ft. or to the structural ceiling, for electrical installations only. (drop ceiling with removable tiles are exempt)

  • 17 years ago

    I actually rethought the use of the space. The 1500 wasn't an impossibility, but, it definitely encouraged more creative thinking (and remeasuring).

    The reason to move it was I was considering making the room a theater, and was going to put the screen on the wall where the panel is. I would then have to figure out how to access the panel.

    In my remeasure I realized I can put the screen on the wall with the pvc pipe. Access for a sewage cleanout is a lot easier and hopefully less frequently accessed.

    Interesting about the limits on distance and placement.

  • 17 years ago

    In my finished basement (BC Canada) the box is slightly recessed into the wall (being a stud wall over concrete retaining with a - pony wall? - above it, then there is a trimmed wooden panel with fittings that snaps in over the panel (don't know if that's kosher now) with a picture hook attached, so it is meant to be covered with a picture. It's not stuck in a corner though, but it might be better if it was.

  • 8 years ago

    I have the same question, but my panel is on a wall that i want removed so that I can expand my teeny tiny kitchen. I want to remove the door and put the panel there instead (see photo.) Since it will be just inches away, I would think it would just be a matter of moving the wires and box all at once. I have no idea, but that's why I'm posting my question here. Seriously, whoever designed my house must have been drunk or an idiot because there's so many things that if they would have just done them differently, it would have made everything so much better.


  • 8 years ago
    last modified: 8 years ago

    The proposed new location is just inches away, but it might as well be feet or yards.

    Moving a panel isn't trivial. You don't just unbolt it and move it over. When your house was wired, the cables (or whatever wiring system was used) were cut to the exact length needed to reach the panel in its current location. Moving the panel means that the electrician has to shorten or extend those cables.

    Shortening isn't so much of a problem, but cables don't stretch, so lengthening cables means they have to be spliced. That's where things get complicated.

    The splices have to be made in junction boxes that remain accessible, in case the splices should fail sometime in the future. (Yes, it happens.) They can't be just buried in the wall.

    Depending on how the cables are currently routed, some might be spliced in junction boxes in the attic or cellar / crawl space. Others may require blank-cover boxes in walls, and/or partial rewiring.

    Also keep in mind that a change of this scale is likely to bring in some requirements for code related updating.

    I don't see any way to guess from here how much labor would be required for this job. Before you go any further with your remodeling project, I suggest that you talk to some local electricians to get a sense for what you're getting into. You might decide that this is a golden opportunity for you to sell this place and move to your dream house with your dream kitchen.

  • 8 years ago
    last modified: 8 years ago

    We're well past this guy's project date, but I wonder why he didn't consider an in-ceiling screen for his theater room, one that would have dropped down when in use? Surely would have been cheaper than a $1500 wiring job.

  • PRO
    7 years ago
    last modified: 7 years ago

    Cheaper and easier to simply build a closet around it!