Software
Houzz Logo Print
service1956

Cannot figure out problem on my stove!

9 years ago

Have a gas stove/range that does not fire. It has the spark ignition that sends high voltage to the igniter mounted on the oven burner. When I try starting it, I see no spark across the gap on igniter but, I can hear the spark jumping behind the upper back panel. So I take the back off and notice the spark arcing on the back side of the ignition module between two points. It is an electronic printed circuit board. The problem I cannot figure out, is that the arcing that is occurring between two points on the back side of the board is almost 3/4 of an inch. And the gap on the igniter is less then 1/4". I checked for resistance on the igniter and it checked at less than 1 ohm. The same with the high voltage wire that goes from the module to igniter.

Now I always thought that high voltage jumps at the point of least resistance.

Could someone please tell me why this could be happening, and how I can correct it?

Comments (6)

  • 9 years ago

    The air gap is going to have a resistance of way more than one ohm. I'm not sure what you are measuring. Any chance that there's some relatively conductive gook on the circuit board where the arcing is occuring? It's also possible that whatever insulation that is supposed to have been there has broken down. I'd also make sure there is continuity between the igniter power supply all the way up to the igniter tip at the burner (and the power supply and the body of the burner that the spark is supposed to jump to are both bonded to the ground).


  • 9 years ago

    By measuring continuity on the igniter from where the H.V. wire connects, to the small rod tip that passes through the porcelain insulator had less than 1 ohm. That confirmed no break that I could not see. As far as the back side of the spark module where the arcing is, has no insulation at. I then took some rubbing alcohol and thoroughly cleaned that area. I then looked with a magnifying glass and saw no evidence of a problem, "conductive path". And the H.V. wire from module to igniter is good with less than 1 ohm of resistance. The darn thing is still arcing! Sure has me stumped!

  • 9 years ago

    Some more or less random thoughts:

    Do the burners also fail to light? The few gas ranges I have experience with have all had a single HV (high voltage) ignitor module that drove all the spark ignitors at once when any burner or the oven was turned on. If all of the HV (high voltage) from your ignitor module is really going to that spark on its board, there should be little or none for the burners too.

    Check to make sure there's an intact grounded electrode on the oven ignitor for the spark to jump to, that it's clean, and that it's grounded. Think of this as like the spark plugs in your car; if they're not clean and properly gapped, they won't ignite the fuel properly.

    You may have some carbon tracking on the HV ignitor board. That would short-circuit the spark. Totally off the top of my head (I haven't actually had to do this) I might try rubbing lightly with a pencil eraser between the board's contact pads, followed by another alcohol wipedown.

    If that fails, you might have to replace the HV module.

    Before dropping big bucks on a factory replacement that might or might not fix the problem, stop by a local used appliance store (you usually find them in the lower income neighborhoods) and see if they'll sell you a used one for cheap, probably around half the new price. Take the original with you. The used appliance stores I've gone to tended to match parts up by appearance.


  • 9 years ago

    You don't indicate how old stove/oven is, but I believe all of the newest ones use a glow plug to ignite the oven and broiler portions of the stove. My stove from 2003 had the glow plugs for oven and broiler, sparker for the stove burners. My 2016 unit works the same way.

  • 9 years ago

    My stove is only 2 years old. A Whirlpool brand that was bought from Home Depot. The oven / broiler has an electronically controlled spark ignition circuit that cuts out after about 5 seconds. Then after 40 seconds, it sparks for another 5 seconds, then cuts out until I manually try to restart it again. I am sure it is a safety feature that keeps gas from building up inside the closed oven. The four burners on the top are controlled from a different spark module that continually sparks until you advance the control knob from Ignite to the High-Medium-Low setting, or the Off position.

  • 8 years ago

    I'm late to this conversation, but have a similar problem with my 3yr old LG range. My top burners work fine, but the oven rarely lights and if it does, it doesn't refire to retain heat for more than a 15min use.

    Research found lots of threads with the conclusion that the igniter inside the oven has gone bad and is a DIY replacement.

    Also found a non-logical, but functional work around. Light a burner on the stove top first (the smallest at the lowest setting is enough), then turn on the oven. I have to leave the burner on the whole time, but I usually need one when cooking anyway, so it's not wasted.

    Not sure if LG and Whirlpool share assembly plants, but like auto air bags, there may be a common manufacturer for the igniters and other internal switches.