Software
Houzz Logo Print
fleshbits

My AC Filter goes in here?

7 years ago

I feel really dumb for asking, but I've never owned a house before. This one I just bought, has a space in my hallway that looks like it is where the AC filter goes. Problem is, I don't see what holds it in. There is no lip. I see some thin metal that almost looks like it folds around the edges. Maybe those are supposed to fold down or something? What is supposed to hold it in? Is this the right spot to put it in?


I took off the grate cover. Had 8 screws. Maybe it is just supposed to rest on the cover? Doesn't seem air tight if I do that.





Comments (19)

  • 7 years ago

    The A/C filter should be in the return air by the A/C plenum. There should be a grill over that opening. Some return air grilles have a filter also.

  • 7 years ago

    Yea, I took the grill off to take a look. I just don't see what holds the filter in place. does it just rest on the grill?

  • 7 years ago

    In my house, the picture is of an air intake. As geoffrey wrote, your air filter(s) should be in a plenum.

  • 7 years ago

    You need to go into the attic and see if there is a filter rack located next to the furnace or air handler. The return you are showing is not set up to hold a filter. Even if it did the opening seems to be too small.

  • 7 years ago

    The filter will be on the suction/intake side of the A/C. That looks like a supply vent, since the intake plenum is usually about 2'x2' (or more).

    Bruce

  • 7 years ago
    last modified: 7 years ago

    Grate I took off:


    I don't see any other openings on the inside of the house anywhere that could possibly be it. It measures 30x18

  • 7 years ago

    Can you post some pictures of your furnace?

  • 7 years ago

    In my house there's a filter that sits inside a grille like that. House was built in the '50s but I don't know when the HVAC went in (probably the 50s).

  • 7 years ago
    last modified: 7 years ago

    I dunno what one looks like, but I will look for objects in the attic


  • 7 years ago

    You can confirm that's an intake/return by turning the system on and
    checking if air blows from there (supply) or sucks air in (return). It appears to be a return per the style of the grate, which appears to be only a cover that fits over the intake plenum, without a frame to hold a filter. The filter probably goes somewhere on the air handler/blower unit, wherever it may be (in your attic?).

  • 7 years ago
    last modified: 7 years ago



    The hole we were discussing is connected to the duct coming in from the Z plane (the back of our perspective. The duct in coming from the top left of the photo, if we are talking 2D

    .

  • 7 years ago

    Also, I held cardboard to the hole in question. It has suction for sure. Maybe the builder skipped putting whatever mechanism would hold the filter in place, inside the hole?

  • 7 years ago

    If it has screws holding it in, and not a couple of half turn clips or latches, it likely ISN'T for a filter. Since it has suction, the filter location should be upstream. The grey cabinet labeled "Honeywell" looks to be the media cabinet that should contain a 4" or so filter, see this link: https://customer.honeywell.com/resources/techlit/TechLitDocuments/68-0000s/68-0239ef.pdf


    You would open that panel and check the listed size of the filter and get a replacement in that size. These babies need changed between every three to six months, on average.

  • 7 years ago

    You rock!


  • 7 years ago

    The good news a filter cabinet was installed at the furnace. You only have to change one filter even if you have multiple returns. The 4 inch size means you don't have to change it as often compared to a one inch filter.

    There seems to be no insulation underneath the furnace. Does the furnace sit above conditioned space? If it is then you need to add insulation.

    Is this furnace set up as a down flow configuration? It looks like there is a damper on the duct on the upper left. Are there multiple zones in the house? I see two other wires. Is one for the thermostat and the other for another damper control?

    The gas input is connected to black pipe and then a flexible connection. What is supporting the black pipe?

    Is the power switch to the furnace near by? It is not in the photo.

  • 7 years ago
    last modified: 7 years ago

    @Mike I dunno what constitutes a zone or what a damper control is. I have one thermostat in the hallway. The furnace is right above the garage, while I am standing on the attic access stairs in the same hallway where the thermostat lives. I haven't seen a power switch, but will look more closely when I get home at that and the black pipe.

  • 7 years ago

    In my opinion, this is the ideal time to find and use an expert. As a home owner, you will want a regular inspection of your A/C and Heating systems. I have my long time A/C company check my units every April or so. Ask around your circle of friends and find a good company or individual to service your equipment, and verify the individual/company works with Lennox equipment (which can be a bit particular, as the parts are generally propriatory and often need to be ordered).

    Then audition the individual/company by having them out to inspect the system, while you are there with them to ask some questions. Yes, it will cost a little more than a simple system check, but you need to understand the system too.

  • 7 years ago

    "Lennox equipment... can be a bit particular, as the parts are generally propriatory and often need to be ordered."

    Is there any home HVAC manufacturer that isn't this way?

    The tenants in one of my rentals keep hounding me for a new furnace to replace the inefficient 1960-vintage monster in their cellar. But that old furnace is super reliable, and when it does break, it's cheap and easy to repair. Blower motor, gas valve, and thermocouple all can be replaced by the universal parts the HVAC tech carries on his truck. The heat is back on in a matter of hours.

    I wouldn't mind upgrading them to something with decent efficiency, either 80% or 90+%, if I could be assured that the new furnace would be equally reliable, and almost as quick and easy to fix.