Software
Houzz Logo Print
sara_huttenga

backsplash help

last month

I am still stuck what to do for backsplash. We have Calacutta Sands quartz. I got these few samples. I have all stainless steel appliances just have not installed them yet. I am also stuck at what to do to the right of the cabinet. The shelf is coming down. Do I put a long shelf or a few? It’s very unfinished and I am lost.

Comments (10)

  • PRO
    last month

    Nice kitchen so far, love the color palette. Of the tile samples shown I would use the square white for the backsplash. As far as the shelf goes, it looks out of place. Ideally a double cabinet should go there. You’re almost finished , nice job.

  • last month

    You can continue the slab counter material as your backsplash. The install is less labor.

  • last month

    We got the Quartz from Menards and installed it ourselves. We are no comfortable doing it asbacksplash. But we are ok with doing some kind of tile ourselves.

  • last month
    last modified: last month

    Love the cab color!

    I’m not normally a fan of open shelves but I think a few simple floating shelves the same color as the cabs could finish that area. I would make sure they were not too skinny as they’ll feel anemic/unbalanced next to the cabs (floating with no hardware will keep them simple)

    for backsplash, I’d be tempted to get something that pulls the green and white together - not this exactly but the idea of some color and pattern - but still somewhat simple so as not to compete with the counters



  • last month
    last modified: last month

    Decide on the feel you want for the kitchen overall and be sure to tie in the flooring. Unless you love one of the three, I’d look for more texture.



    Suggest floating shelves vs brackets, ending where counter ends.



  • PRO
    last month

    IMO get another slab ofquartz and do it all to match the range has a back so caan even go there

  • last month
    last modified: last month

    Matching slab will give you a higher end look. Templating and accurately cutting is the procedures you could focus on.

    AI= Step-by-Step Installation:

    1. Prepare the Wall: Ensure the wall is clean, smooth, and free of grease or debris; scraping off old adhesive is key.
    2. Dry Fit: Place the quartz slab against the wall to check alignment and mark any cuts needed for outlets or corners.
    3. Apply Adhesive: Apply generous dabs or a continuous zigzag bead of silicone adhesive to the back of the quartz, keeping it away from edges to prevent excessive squeeze-out.
    4. Mount the Slab: Press the backsplash firmly onto the wall, aligning it with your markings; use a level to confirm it's straight.
    5. Secure & Smooth: Hold it in place with painter's tape. Use a spray mist (water/mild soap mix) and a finishing tool to smooth the silicone bead where the slab meets the wall and countertop for a clean seal.
    6. Cure: Let the adhesive set, typically 20-30 minutes to start, but allow up to 24 hours for full curing before removing tape or using the counter.

    Tips for Success:

    • Use Big Dots: Applying large dots of silicone can provide better hold with less mess than squiggles.
    • Work in Sections: For large pieces, install in manageable sections.
    • Clean as You Go: Wipe away excess silicone immediately with a damp rag before it sets.
    • Your wall area looks fairly straightforward. I'd think about it. Here's a Houzz article-

    Why You Should Embrace a Solid Slab Backsplash

    Cutoff disc. Durable Diamond Angle Grinding Wheel

  • last month
    last modified: last month

    I would remove the other upper and leave that wall open for open shelves. run the backsplash all the wal to the soffit, ending at the end of the countertop.

    a subway tile in a running bond pattern, and do the stove wall backsplash an entirely different tile.

    that green tile would be great on the stove side. google styling open kitchen shelves and see some ideas... even add a light above it to accent.


  • last month

    Hi @Sara H, people often feel lost as they near the end. You’ve done such a good job already, I don’t doubt you’ll do a good job with the tile as well. My first recommendation is that you use a brand like Daltile or American Olean, big companies that make tile and all the matching trim pieces you might need. Something as simple as a bullnose tile can make a huge difference in the appearance of the finished installation. Daltile is great quality tile and relatively inexpensive. You can find it at big box stores or order it online.

    Next, I’d keep the tile neutral in color and light, because even in daylight that space is very dark. Finally, bring home several whites and greys and look at them in your space in your light before you choose a tile. I’m sure you’ll find something fantastic. This is Daltile Matte Arctic White in a 4” square.



  • last month

    Love your white foursquare sample.