Software
Houzz Logo Print
kren_pa

k n t, the time has come..

18 years ago

hello all

we have one remaining K and T circuit in our 1922 home...it supplies the first floor ceilings which are lath and plaster. we have fished wires in the past, and have recently redone a number of outlets that were on this circuit, as well as two ceiling lights (started from the end of the circuit, capped them off in boxes). i would like to get rid of the rest of this circuit.

my question for you is..if we fish up through the walls (also plaster, sadly, then between two ceiling joists to get to the fixture, how do we get around the corner where the wall and the ceiling meet? in one room in particular, the wall is the main support of the upstairs and i don't want to damage anything supporting the upper floor. what have your experiences been with knob and tube replacement? i should say that my hubby does all of the actual electrical as he knows much more about how K and T works...however, he refuses to fish wires-- that is my job. if i can get them fished, he will do the rest. thanks for any advice you might have kren

Comments (7)

  • 18 years ago

    the only way to fish around a corner is to have access. this means if you do not have attic/crawlspace access to feed from abov eor below, you will have to cut open the wall or ceiling in at least 1 room.

    i honestly would try to fish from above/below versus doing this, unless you just have no other choice. plaster/lathe repair is a lot more involved than patching sheetrock.

  • 18 years ago

    hi there
    thanks for your helpful message...we do not have access, there is a wall on the second floor and the floor itself is tongue and groove boards. on the first floor, both wall and ceiling are plaster so there are holes that will have to be made. that's ok, i am wondering how to go around the corner, once i am inside the wall...do you drillup through the stud running along the top of the wall? and then across and through the ceiling joists?

    i have patched lath and plaster...but never tongue and groove wood floor..

    kren

  • 18 years ago

    ok, i just reread your post and realize you meant the corner at the intersection of the wall and ceiling, i thought you meant around a wall corner for some reason!

    if you have a long fish tape, and a long drill bit, you can drill all the way up thru the top plate of the wall straight out from where you are runnign the wire to. remove the existing fixture, then from below fish the tape up thru the wall and into the joist cavity. you may need a second tape to grab teh first one, but sometimes you push it and it go inthe correct direction. once the fish tape comes out at the fixture, attach the new cable and pull it back thru. be careful at the point it turns to go down the wall, it probably will hang up. if it just refuses to pass this point, your only option is to cut either the ceiling or the wall, and maybe both to feed it around and down.

  • 18 years ago

    That's called a top plate, drill straight up through it and you should be in between the floor/ceiling joists. If possible run the electric up the wall that lets you get in between the joists rather than have to go thru half of them to get to the light in the center of the room. Punch one hole in the wall to allow you to drill into the top plate and one hole in the ceiling to pull the wire.

    This should work for convential and balloon framing.

  • 18 years ago

    If you have wood lath, as long as you can make any larger holes parallel to the lath it is not very hard to fix.
    If you have to cut a larger opening then just square it off as well as you can.
    Use construction adhesive (it often takes a pretty big blob to reach past the keys on the lath) and drywall screws to fasten some 1x2 strips at each side of the opening in the wall and spanning.
    Fasten a piece of 1/2 inch drywall to the strips after the glue has set up using drywall screws.
    You should cut the drywall to about 1/2 inch smaller than the opening in both dimensions (leave ~1/4 inch gap from the old to the drywall base.
    Use Easysand to build the surface back up to flush.
    Mix the Easysand about as thick as peanut butter and mist the edges of the old plaster (or even paint them with elmers white glue mixed 50/50 with water).
    It will take a couple layers to get everythig back to flush and smooth.
    Easysand mixed this way has very little shrinkage as it sets (it does NOT set by drying byt by chemical reaction, just like the old plaster lime putty mix).
    All these techniques work with gypsum backer board (and even expended metal).

  • 18 years ago

    this is awesome, just returned to this message and found all the new advice!! these instructions correspond to what i was thinking of doing, which is a nice confirmation. of course now i have to do it!!
    i confess i have been using lightweight joint compound to fix plaster holes, but i will be looking for "easysand"!!
    i thought you had to use real plaster (and i realize that is nicer in an historic home) until i watched my neighbor fixed a 1 x 10 foot hole with joint compound.
    thanks for your help!
    kren

  • 18 years ago

    The problem (even with the available 'patching plaster') is that the set time is way to fast for working surfaces.

    Plain lime plaster was used for many years, but it can take an entire year to actually cure. It absorbs CO2 from the air as part of the curing process.

    Adding 'gaging plaster' to the lime putty creates a material with a longer set time, but it still has many of the desirable surface working properties of lime plaster.

    If someone wants the full restoration (wood lath, hair, 3 coats, etc.) I can do the work (though my older plasterer died a while ago).
    If you want something that looks the same and has the same sound characteristics 2 coat plaster of gypsum backer is much more economical.
    You can even save some more money at a loss in the sound transmission you can use a veneer plaster system.
    1/2 inch backer (AKA 'blueboard') with a thin (~1/8 inch) layer of plaster.
    'Plastering Skills' by F. Van Den Brandon is a good introduction.

    Here is a link that might be useful: Plastering Skills