- All Products
- Bath
- Tile
- Width: 11 To 12 Inches
Thin Contemporary Blue 11 to 12 Inch Wide Tile
- 10.5 square feet, 10 pieces per case. Case weight is 18.02 lbs.
- Grade 1, first-quality porcelain tile for floor and wall use
- 11.88 in. width x 12.63 in. length x 0.21 in. thick mesh-mounted mosaic
- Glazed, smooth finish with a high sheen and slight variation in tone
- PEI Rating III is suitable for medium-duty residential floors including kitchens, halls, corridors, balconies, terraces and areas used more often with normal footwear and small amounts of dirt
- Impervious tiles have a water absorption of less than 0.5% for indoor and outdoor use and are frost resistant
- This tile is not ADA approved for slip resistance with a DCOF value less than 0.42.
- Completely frost resistant for indoor or outdoor applications; use a latex-modified thinset for acceptable bond strength
- Please note: Samples are not returnable
- Country of Origin: Indonesia
Pool Rated for use in Swimming Pools
** Price is per Piece **
- Material: Handmade Porcelain
- Piece Size: 11 1/2" x 11 1/2"
- Sq Ft Per Piece: 0.92
- Thickness: 1/4"
- Color: Royal Blue
- Finish: Glossy
For use in
- Pools, Pool Liners
- Interior Dry Walls
- Interior Floors
- Shower Walls, Shower Floors
- Exterior Walls, Exterior Floors
- Pool rated and acceptable for use on shower walls.
- The polyurethane cord backing makes installation easy.
- For use in Pools, Pool Liners, Shower Walls, Interior Dry Walls
- Installation Guide
Recommended Substrates:
- Properly cured mortar beds-ANSI A108.1B (cured a minimum of 7 days).
- Cementitious backer units (CBU)-ANSI A118.9.
- Concrete slabs cured for 28 days minimum.
- Gypsum board (dry areas only)-ASTM C1396 or ASTM C1396M-04.
- Note: An ANSI A108A-2.1.8 membrane is required behind all CBU installations in wet areas.
Setting Materials & Methods:
Setting material requirements will vary dependent upon the type of mosaic product being installed and the nature of the substrate.- Advice on the appropriate setting materials should be sought from your tile and stone dealer at the time of purchase.
- Only use setting materials that meet or exceed TCNA guidelines
- Only use an accredited licensed contractor experienced in the art of installing mosaic products.
- Setting methods must conform to the TCNA guidelines.
Acceptable Thin-Sets (White Color):
- MAPEI: Adesilex P10 Bright White Thin-Set Mortar mixed With Keraply Mortar Additive
- BOSTIK: Glass-Mate™ GLASS TILE MORTAR
- BOSTIK: ReFlex Ultra-Premium Latex Modified Thin-Set Mortar
- LATICRETE: Glass Tile Adhesive
- TEC SPECIALTY PRODUCTS: Super Flex Premium Performance Universal Latex-Modified ThinSet Mortar
Note: Grout Selection:
The use of sanded and some premixed urethane micro glass bead enhanced grouts may cause damage to scratch sensitive surfaces. Always check with your Stone and Tile Dealer, Setting Contractor or Grout Manufacturer before selecting the grout type. Maniscalco is not responsible for any damage to the tile surface due to incorrect grout selection or incorrect grouting procedures.Measuring: Measure coverage area, make sure to purchase at least 10% extra material than is required. This will account for any breakage or mis-cuts during installation, and ensure you have extra material should you have to replace any tile elements in the future.
Cutting: Plan the placement of the tiles on your wall prior to installation. If you need to cut a mosaic sheet, cut from the back using a utility knife between tiles along the grout joints. Should you need to cut across tiles in a fashion that is not possible with a utility knife, use a wet saw with a diamond blade to cut through the tile.
Drilling: Using a drill bit designed for glass is recommended. When drilling the hole, keep the bit and hole lubricated to prevent chipping. Start by drilling from both ends of the tile, starting with the back and drilling half the depth of the tile. Then, turn the tile over and complete the hole is recommended. This will prevent the glass from chipping as the drill bit exits the tile.
Applying Setting Materials:
Apply setting material using the notched side of a V-notched trowel. Using the flat side of the trowels, smooth out all ridges to achieve a consistent, even 1/8” (3mm) coverage.Apply glass mosaic sheets, mesh -side down, firmly into freshly laid setting material. Mix and match from assorted sell units to achieve consistent variation. Using a rubber grout float gently press the tile into adhesive to ensure complete contact.
Natural Stone should be sealed prior to grouting. A premium penetrating sealer is recommended for a natural look. Please refer to sealer manufacturer’s recommendations for application instructions.
Cleaning: Clean all excess grout immediately with a damp sponge. After 12 hours polish off any remaining haze with a dry cloth or towel. For tough stains, we require the use of PH Neutral cleaner to clean the tile and grout, such as Grout & Tile neutral cleaner.
MAINTENANCE & CARE
Required to use a soft bristle brush to scrub the tile surfaces and grout. Take care to only use a soft bristle brush, to avoid the chance of scratching or damaging the grout. Then, simply wipe the surface, rinse well with clean water, and dry with a soft clean towel.
Required to use PH Neutral Cleaner to clean the tile and grout, such as Grout & Tile Neutral Cleaner
We strongly recommend customers to use a licensed tile contractor to do the tile installation and always use TCNA tile installation handbook as the installation guidance
Tile Maintenance and More
Colors may vary from picture, Product may have chips, pitting and other characteristics, Pictures are only an indication of color, texture and finish
- 11.2 square feet, 10 pieces per case. Case weight is 19 lbs.
- Grade 1, first-quality porcelain tile for floor and wall use
- 11.88 in. width x 13.25 in. length x 0.19 in. thick mesh-mounted mosaic
- Glazed, smooth finish with a high sheen and slight variation in tone
- PEI Rating IV has high resistance to abrasion and is suitable for heavy-duty residential and commercial kitchens, hotels, exhibition and sales rooms with some dirt conditions
- Impervious tiles have a water absorption of less than 0.5% for indoor and outdoor use and are frost resistant
- This tile is not ADA approved for slip resistance with a DCOF value less than 0.42.
- Completely frost resistant for indoor or outdoor applications; use a latex-modified thinset for acceptable bond strength
- Please note: Samples are not returnable
- Country of Origin: Indonesia
- Blue 11"x10" beautiful swimming pool ceramic tile with Large Gecko design
- Handcrafted in the USA from high quality ceramic tile
- Pre-assembled and ready for installation
- Hand Glazed Style, Thickness: 1/4 inch
- Lifetime Warranty
Pool Rated for use in Swimming Pools
Price per Sheet
Water jet The Rift glass piece precisely cut to create perfect wave-like pattern.
- Material: Glass
- Piece Size: 11 1/2" x 12 1/2"
- Sq Ft Per Piece: 1
- Thickness: 3/8"
- Colors: The Rift
- Finish: Glossy
- Brighten up your pool or shower with this series
- Pool rated and acceptable for use on shower walls.
- The polyurethane cord backing makes installation easy.
- For use in Shower Walls, Shower Floors, Pools, Pool Liners, Interior Dry Walls, Interior Floors, Exterior Walls
- Installation Guide
Recommended Substrates:
- Properly cured mortar beds-ANSI A108.1B (cured a minimum of 7 days).
- Cementitious backer units (CBU)-ANSI A118.9.
- Concrete slabs cured for 28 days minimum.
- Gypsum board (dry areas only)-ASTM C1396 or ASTM C1396M-04.
- Note: An ANSI A108A-2.1.8 membrane is required behind all CBU installations in wet areas.
Setting Materials & Methods:
Setting material requirements will vary dependent upon the type of mosaic product being installed and the nature of the substrate.- Advice on the appropriate setting materials should be sought from your tile and stone dealer at the time of purchase.
- Only use setting materials that meet or exceed TCNA guidelines
- Only use an accredited licensed contractor experienced in the art of installing mosaic products.
- Setting methods must conform to the TCNA guidelines.
Note: Grout Selection:
The use of sanded and some premixed urethane micro glass bead enhanced grouts may cause damage to scratch sensitive surfaces. Always check with your Stone and Tile Dealer, Setting Contractor or Grout Manufacturer before selecting the grout type. Maniscalco is not responsible for any damage to the tile surface due to incorrect grout selection or incorrect grouting procedures.Measuring: Measure coverage area, make sure to purchase at least 10% extra material than is required. This will account for any breakage or mis-cuts during installation, and ensure you have extra material should you have to replace any tile elements in the future.
Cutting: Plan the placement of the tiles on your wall prior to installation. If you need to cut a mosaic sheet, cut from the back using a utility knife between tiles along the grout joints. Should you need to cut across tiles in a fashion that is not possible with a utility knife, use a wet saw with a diamond blade to cut through the tile.
Drilling: Using a drill bit designed for glass is recommended. When drilling the hole, keep the bit and hole lubricated to prevent chipping. Start by drilling from both ends of the tile, starting with the back and drilling half the depth of the tile. Then, turn the tile over and complete the hole is recommended. This will prevent the glass from chipping as the drill bit exits the tile.
Applying Setting Materials:
Apply setting material using the notched side of a V-notched trowel. Using the flat side of the trowels, smooth out all ridges to achieve a consistent, even 1/8” (3mm) coverage.Apply glass mosaic sheets, mesh -side down, firmly into freshly laid setting material. Mix and match from assorted sell units to achieve consistent variation. Using a rubber grout float gently press the tile into adhesive to ensure complete contact.
Natural Stone should be sealed prior to grouting. A premium penetrating sealer is recommended for a natural look. Please refer to sealer manufacturer’s recommendations for application instructions.
Recommended Thin-Set: MAPEI Adesilex-P10 Premium Glass Tile Mortar mixed with MAPEI Keraply Latex Mortar Additive
Suggested Grout: MAPEI Ultracolor Plus FA, MAPEI FlexColor CQ or BOSTIK Trucolor Rapidcure
Cleaning: Clean all excess grout immediately with a damp sponge. After 12 hours polish off any remaining haze with a dry cloth or towel. For tough stains, we require the use of PH Neutral cleaner to clean the tile and grout, such as Grout & Tile neutral cleaner.
MAINTENANCE & CARE
Required to use a soft bristle brush to scrub the tile surfaces and grout. Take care to only use a soft bristle brush, to avoid the chance of scratching or damaging the grout. Then, simply wipe the surface, rinse well with clean water, and dry with a soft clean towel.
Required to use PH Neutral Cleaner to clean the tile and grout, such as Grout & Tile Neutral Cleaner
We strongly recommend customers to use a licensed tile contractor to do the tile installation and always use TCNA tile installation handbook as the installation guidance
Colors may vary from picture, Product may have chips, pitting and other characteristics, Pictures are only an indication of color, texture and finish
- 9.7 square feet, 10 pieces per case. Case weight is 20.78 lbs.
- Grade 1, first-quality porcelain tile for floor and wall use
- 10.88 in. width x 12.63 in. length x 0.19 in. thick mesh-mounted mosaic
- Glazed, smooth finish with a high sheen and slight variation in tone
- PEI Rating II is suitable for all interior walls and light foot traffic such as powder rooms
- Impervious tiles have a water absorption of less than 0.5% for indoor and outdoor use and are frost resistant
- This tile is not ADA approved for slip resistance with a DCOF value less than 0.42.
- Completely frost resistant for indoor or outdoor applications; use a latex-modified thinset for acceptable bond strength
- Please note: Samples are not returnable
- Country of Origin: Indonesia
- 9.8 square feet, 10 pieces per case. Case weight is 24.3 lbs.
- Grade 1, first-quality porcelain tile for floor and wall use
- 11.75 in. width x 11.75 in. length x 0.28 in. thick mesh-mounted mosaic
- Glazed, smooth finish with a high sheen and slight variation in tone
- PEI Rating II is suitable for all interior walls and light foot traffic such as powder rooms
- Impervious tiles have a water absorption of less than 0.5% for indoor and outdoor use and are frost resistant
- This tile has a COF wet rating less than or equal to 0.50 and is considered to have a marginally low skid resistance. This tile is not ADA approved for slip resistance.
- Completely frost resistant for indoor or outdoor applications; use a latex-modified thinset for acceptable bond strength
- Please note: Samples are not returnable
- Country of Origin: Thailand
- Material: Glass
- Individual Tile Size: 2"x2"
- Sheet Size: 11-3/4 in. x 11-3/4 in. x 8 mm
- Coverage: 0.97 sqt/sheet, 10 sheets per case covers 9.7 sqt
- Usage: Kitchen and Bath Backsplash, wall Tile
Pool Rated for use in Swimming Pools
Price per Sheet
Water Blue-Water jet mosaic, white, light blue and dark blue glass in water wave interlocking pattern art mosaic
- Material: Glass
- Piece Size: 11 1/2" x 12 1/2"
- Sq Ft Per Piece: 1
- Thickness: 3/8"
- Colors: Ocean Blue
- Finish: Glossy
- Brighten up your pool or shower with this series
- Pool rated and acceptable for use on shower walls.
- The polyurethane cord backing makes installation easy.
- For use in Shower Walls, Shower Floors, Pools, Pool Liners, Interior Dry Walls, Interior Floors, Exterior Walls
- Installation Guide
Recommended Substrates:
- Properly cured mortar beds-ANSI A108.1B (cured a minimum of 7 days).
- Cementitious backer units (CBU)-ANSI A118.9.
- Concrete slabs cured for 28 days minimum.
- Gypsum board (dry areas only)-ASTM C1396 or ASTM C1396M-04.
- Note: An ANSI A108A-2.1.8 membrane is required behind all CBU installations in wet areas.
Setting Materials & Methods:
Setting material requirements will vary dependent upon the type of mosaic product being installed and the nature of the substrate.- Advice on the appropriate setting materials should be sought from your tile and stone dealer at the time of purchase.
- Only use setting materials that meet or exceed TCNA guidelines
- Only use an accredited licensed contractor experienced in the art of installing mosaic products.
- Setting methods must conform to the TCNA guidelines.
Note: Grout Selection:
The use of sanded and some premixed urethane micro glass bead enhanced grouts may cause damage to scratch sensitive surfaces. Always check with your Stone and Tile Dealer, Setting Contractor or Grout Manufacturer before selecting the grout type. Maniscalco is not responsible for any damage to the tile surface due to incorrect grout selection or incorrect grouting procedures.Measuring: Measure coverage area, make sure to purchase at least 10% extra material than is required. This will account for any breakage or mis-cuts during installation, and ensure you have extra material should you have to replace any tile elements in the future.
Cutting: Plan the placement of the tiles on your wall prior to installation. If you need to cut a mosaic sheet, cut from the back using a utility knife between tiles along the grout joints. Should you need to cut across tiles in a fashion that is not possible with a utility knife, use a wet saw with a diamond blade to cut through the tile.
Drilling: Using a drill bit designed for glass is recommended. When drilling the hole, keep the bit and hole lubricated to prevent chipping. Start by drilling from both ends of the tile, starting with the back and drilling half the depth of the tile. Then, turn the tile over and complete the hole is recommended. This will prevent the glass from chipping as the drill bit exits the tile.
Applying Setting Materials:
Apply setting material using the notched side of a V-notched trowel. Using the flat side of the trowels, smooth out all ridges to achieve a consistent, even 1/8” (3mm) coverage.Apply glass mosaic sheets, mesh -side down, firmly into freshly laid setting material. Mix and match from assorted sell units to achieve consistent variation. Using a rubber grout float gently press the tile into adhesive to ensure complete contact.
Natural Stone should be sealed prior to grouting. A premium penetrating sealer is recommended for a natural look. Please refer to sealer manufacturer’s recommendations for application instructions.
Recommended Thin-Set: MAPEI Adesilex-P10 Premium Glass Tile Mortar mixed with MAPEI Keraply Latex Mortar Additive
Suggested Grout: MAPEI Ultracolor Plus FA, MAPEI FlexColor CQ or BOSTIK Trucolor Rapidcure
Cleaning: Clean all excess grout immediately with a damp sponge. After 12 hours polish off any remaining haze with a dry cloth or towel. For tough stains, we require the use of PH Neutral cleaner to clean the tile and grout, such as Grout & Tile neutral cleaner.
MAINTENANCE & CARE
Required to use a soft bristle brush to scrub the tile surfaces and grout. Take care to only use a soft bristle brush, to avoid the chance of scratching or damaging the grout. Then, simply wipe the surface, rinse well with clean water, and dry with a soft clean towel.
Required to use PH Neutral Cleaner to clean the tile and grout, such as Grout & Tile Neutral Cleaner
We strongly recommend customers to use a licensed tile contractor to do the tile installation and always use TCNA tile installation handbook as the installation guidance
Colors may vary from picture, Product may have chips, pitting and other characteristics, Pictures are only an indication of color, texture and finish
- 10.5 square feet, 10 pieces per case. Case weight is 18.02 lbs.
- Grade 1, first-quality porcelain tile for floor and wall use
- 11.88 in. width x 12.63 in. length x 0.21 in. thick mesh-mounted mosaic
- Glazed, smooth finish with a high sheen and slight variation in tone
- PEI Rating II is suitable for all interior walls and light foot traffic such as powder rooms
- Impervious tiles have a water absorption of less than 0.5% for indoor and outdoor use and are frost resistant
- This tile is not ADA approved for slip resistance with a DCOF value less than 0.42.
- Completely frost resistant for indoor or outdoor applications; use a latex-modified thinset for acceptable bond strength
- Please note: Samples are not returnable
- Country of Origin: Indonesia
- Full Sheets: $22.95/Sq Ft
- 4" x 6" Samples: $6.99 each
- Dimensions: 1.5" x 0.5" porcelain elongated hexagon on a 10" x 11.5" mesh
- Thickness: 8 mm
- Weight: 3.2 lbs/Sq Ft
- 9.6 square feet, 10 pieces per case. Case weight is 27.6 lbs.
- Grade 1, first-quality porcelain tile for floor and wall use
- 11.63 in. width x 11.63 in. length x 0.25 in. thick mesh-mounted mosaic
- Glazed, smooth finish with a high sheen and slight variation in tone
- PEI Rating II is suitable for all interior walls and light foot traffic such as powder rooms
- Impervious tiles have a water absorption of less than 0.5% for indoor and outdoor use and are frost resistant
- This tile has a COF wet rating less than or equal to 0.50 and is considered to have a marginally low skid resistance. This tile is not ADA approved for slip resistance.
- Completely frost resistant for indoor or outdoor applications; use a latex-modified thinset for acceptable bond strength
- Please note: Samples are not returnable
- Country of Origin: Thailand
- 8.3 square feet, 10 pieces per case. Case weight is 13.65 lbs.
- Grade 1, first-quality porcelain tile for floor and wall use
- 10.75 in. width x 10.88 in. length x 0.25 in. thick mesh-mounted mosaic
- Glazed, smooth finish with a high sheen and moderate variation in tone
- PEI Rating IV has high resistance to abrasion and is suitable for heavy-duty residential and commercial kitchens, hotels, exhibition and sales rooms with some dirt conditions
- Impervious tiles have a water absorption of less than 0.5% for indoor and outdoor use and are frost resistant
- This tile has a COF wet rating greater than 0.60 to 0.79 which is considered skid resistant for indoor and outdoor use. This tile is ADA approved for slip resistance.
- Completely frost resistant for indoor or outdoor applications; use a latex-modified thinset for acceptable bond strength
- Please note: Samples are not returnable
- Country of Origin: Indonesia
Choose to intermix the decor tiles with the regular tiles to create a stunning back drop. Each box comes with an assortment of any of the 9 shades and designs featured in the photos.This assures that each project has that imperfectly perfect look. Please note, shade variations and imperfection between tiles is characteristic of this product line.
- 9 Sq Ft: $162.00
- Please note, this product has a minimum purchase requirement of 9 Sq Ft.
- 5" x 5" Sample: $6.99
- Weight: 3.7 LBS/ Sq Ft
- Individual Tile Pieces: 5" x 5"
- Thickness: 12 mm
- Made in Spain
- Free Shipping on all orders of samples and 8 sq ft or more.
- Sheet size:11.8x11.8"
- Materials:Glass
- Sold by:sheet
- Pcs or shts/box:5 sheets/boxSq.Ft/box:4.83
Swimming Pool and Wet area Tiles
Color Stained glass tile mosaic
*** Price per Sheet (0.96 sq ft) ***
- Material: Glass
- Sheet Size: 11.75" x 11.75"
- Sq Ft Per Piece: 1.00
- Approximate Piece Size: 1" x 1"
- Thickness: 1/4"
- Colors: Light Blue
- Finish: Glossy
- Backing: Face mount
- Brighten up your pool or shower with this series of Handmade Porcelain mosaics.
- Pool rated and acceptable for use on shower walls.
- Use for Interior Dry Walls, Interior Floors, Shower Walls, Shower Floors, Pools, Pool Liners
- Installation Guide
Installation Instructions
Recommended Substrates:
- Properly cured mortar beds-ANSI A108.1B (cured a minimum of 7 days).
- Cementitious backer units (CBU)-ANSI A118.9.
- Concrete slabs cured for 28 days minimum.
- Gypsum board (dry areas only)-ASTM C1396 or ASTM C1396M-04.
- Note: An ANSI A108A-2.1.8 membrane is required behind all CBU installations in wet areas.
Setting Materials & Methods:
Setting material requirements will vary dependent upon the type of mosaic product being installed and the nature of the substrate.- Advice on the appropriate setting materials should be sought from your tile and stone dealer at the time of purchase.
- Only use setting materials that meet or exceed TCNA guidelines
- Only use an accredited licensed contractor experienced in the art of installing mosaic products.
- Setting methods must conform to the TCNA guidelines.
Note: Grout Selection:
The use of sanded and some premixed urethane micro glass bead enhanced grouts may cause damage to scratch sensitive surfaces. Always check with your Stone and Tile Dealer, Setting Contractor or Grout Manufacturer before selecting the grout type. Maniscalco is not responsible for any damage to the tile surface due to incorrect grout selection or incorrect grouting procedures.Colors may vary from picture, Product may have chips, pitting and other characteristics, Pictures are only an indication of color, texture and finish
- 9.8 square feet, 10 pieces per case. Case weight is 18.6 lbs.
- Grade 1, first-quality porcelain tile for floor and wall use
- 11.75 in. width x 11.75 in. length x 0.18 in. thick mesh-mounted mosaic
- Glazed, mixed texture with a mixed finish and slight variation in tone
- PEI Rating IV has high resistance to abrasion and is suitable for heavy-duty residential and commercial kitchens, hotels, exhibition and sales rooms with some dirt conditions
- Impervious tiles have a water absorption of less than 0.5% for indoor and outdoor use and are frost resistant
- This tile has a COF wet rating greater than 0.60 to 0.79 which is considered skid resistant for indoor and outdoor use. This tile is ADA approved for slip resistance.
- Completely frost resistant for indoor or outdoor applications; use a latex-modified thinset for acceptable bond strength
- Please note: Samples are not returnable
- Country of Origin: Indonesia
- Thickness: 8mm
- Fiberglass Mesh Backing for quick and easy installation
- Harmonious color result in unique pieces of art
- Suitable for kitchen / bathroom / wall and etc
- Chemical Resistant
- Fading and Discoloration Resistant
- Frost Resistant
- Mohs Hardness Scale - 6
- Resistant to Temperature Shock
- Size Per Sheet: 11-3/4 in. x 10 in. x 6 mm
- Coverage: 0.82 sqt per sheet
- Type: Porcelain
- Finish: Satin
- Usage: Kitchen and Bathroom Backsplash Wall and Floor Tile
- 10.0 square feet, 10 pieces per case. Case weight is 25.33 lbs.
- Grade 1, first-quality porcelain tile for floor and wall use
- 11.13 in. width x 12.63 in. length x 0.24 in. thick mesh-mounted mosaic
- Glazed, smooth finish with a high sheen and slight variation in tone
- PEI Rating II is suitable for all interior walls and light foot traffic such as powder rooms
- Impervious tiles have a water absorption of less than 0.5% for indoor and outdoor use and are frost resistant
- This tile has no available COF wet rating. This tile is not ADA approved for slip resistance.
- Completely frost resistant for indoor or outdoor applications; use a latex-modified thinset for acceptable bond strength
- Please note: Samples are not returnable
- Country of Origin: Thailand
- MOSAIC PORCELAIN PENNY ROUND - LIGHT BLUE
- Pool Rated for use in Swimming Pools
*** Price per Sheet ***
- Material: Handmade Porcelain
- Piece Size: 11.5"x12.25"
- Individual Size: 3/4"
- Sq Ft Per Piece: 0.98
- Thickness:.25"
- Colors: Light Blue
- Finish: Matte
For use in
- Pools, Pool Liners
- Interior Dry Walls
- Interior Floors
- Shower Walls, Shower Floors
- Exterior Walls
- Pool rated and acceptable for use on shower walls.
- The polyurethane cord backing makes installation easy.
- For use in Pools, Pool Liners, Shower Walls, Interior Dry Walls
- Installation Guide
Recommended Substrates:
- Properly cured mortar beds-ANSI A108.1B (cured a minimum of 7 days).
- Cementitious backer units (CBU)-ANSI A118.9.
- Concrete slabs cured for 28 days minimum.
- Gypsum board (dry areas only)-ASTM C1396 or ASTM C1396M-04.
- Note: An ANSI A108A-2.1.8 membrane is required behind all CBU installations in wet areas.
Setting Materials and Methods:
Setting material requirements will vary dependent upon the type of mosaic product being installed and the nature of the substrate.- Advice on the appropriate setting materials should be sought from your tile and stone dealer at the time of purchase.
- Only use setting materials that meet or exceed TCNA guidelines
- Only use an accredited licensed contractor experienced in the art of installing mosaic products.
- Setting methods must conform to the TCNA guidelines.
Acceptable Thin-Sets (White Color):
- MAPEI: Adesilex P10 Bright White Thin-Set Mortar mixed With Keraply Mortar Additive
- BOSTIK: Glass-Mate GLASS TILE MORTAR
- BOSTIK: ReFlex Ultra-Premium Latex Modified Thin-Set Mortar
- LATICRETE: Glass Tile Adhesive
- TEC SPECIALTY PRODUCTS: Super Flex Premium Performance Universal Latex-Modified ThinSet Mortar
Note: Grout Selection:
The use of sanded and some premixed urethane micro glass bead enhanced grouts may cause damage to scratch sensitive surfaces. Always check with your Stone and Tile Dealer, Setting Contractor or Grout Manufacturer before selecting the grout type. Maniscalco is not responsible for any damage to the tile surface due to incorrect grout selection or incorrect grouting procedures.Measuring: Measure coverage area, make sure to purchase at least 10% extra material than is required. This will account for any breakage or mis-cuts during installation, and ensure you have extra material should you have to replace any tile elements in the future.
Cutting: Plan the placement of the tiles on your wall prior to installation. If you need to cut a mosaic sheet, cut from the back using a utility knife between tiles along the grout joints. Should you need to cut across tiles in a fashion that is not possible with a utility knife, use a wet saw with a diamond blade to cut through the tile.
Drilling: Using a drill bit designed for glass is recommended. When drilling the hole, keep the bit and hole lubricated to prevent chipping. Start by drilling from both ends of the tile, starting with the back and drilling half the depth of the tile. Then, turn the tile over and complete the hole is recommended. This will prevent the glass from chipping as the drill bit exits the tile.
Applying Setting Materials:
Apply setting material using the notched side of a V-notched trowel. Using the flat side of the trowels, smooth out all ridges to achieve a consistent, even 1/8" (3mm) coverage.Apply glass mosaic sheets, mesh -side down, firmly into freshly laid setting material. Mix and match from assorted sell units to achieve consistent variation. Using a rubber grout float gently press the tile into adhesive to ensure complete contact.
Natural Stone should be sealed prior to grouting. A premium penetrating sealer is recommended for a natural look. Please refer to sealer manufacturer's recommendations for application instructions.
Cleaning: Clean all excess grout immediately with a damp sponge. After 12 hours polish off any remaining haze with a dry cloth or towel. For tough stains, we require the use of PH Neutral cleaner to clean the tile and grout, such as Grout and Tile neutral cleaner.
MAINTENANCE and CARE
Required to use a soft bristle brush to scrub the tile surfaces and grout. Take care to only use a soft bristle brush, to avoid the chance of scratching or damaging the grout. Then, simply wipe the surface, rinse well with clean water, and dry with a soft clean towel.
Required to use PH Neutral Cleaner to clean the tile and grout, such as Grout and Tile Neutral Cleaner
We strongly recommend customers to use a licensed tile contractor to do the tile installation and always use TCNA tile installation handbook as the installation guidance
Tile Maintenance and More
Colors may vary from picture, Product may have chips, pitting and other characteristics, Pictures are only an indication of color, texture and finish
- Individual Tile Size: Approx. 1"x4"
- Sheet size: 11-3/4 in. x 11-3/4 in. x 8 mm
- Coverage: 0.97sqt per sheet
- Usage: kitchen and bathroom backsplash, wall tile
- 10.0 square feet, 10 pieces per case. Case weight is 25.33 lbs.
- Grade 1, first-quality porcelain tile for floor and wall use
- 11.13 in. width x 12.63 in. length x 0.27 in. thick mesh-mounted mosaic
- Glazed, smooth finish with a high sheen and uniform appearance in tone
- PEI Rating III is suitable for medium-duty residential floors including kitchens, halls, corridors, balconies, terraces and areas used more often with normal footwear and small amounts of dirt
- Impervious tiles have a water absorption of less than 0.5% for indoor and outdoor use and are frost resistant
- This tile has a COF wet rating less than or equal to 0.50 and is considered to have a marginally low skid resistance. This tile is not ADA approved for slip resistance.
- Completely frost resistant for indoor or outdoor applications; use a latex-modified thinset for acceptable bond strength
- Please note: Samples are not returnable
- Country of Origin: Thailand
Glass tiles are strong, easily cleaned and at the same time both classic and modern making them a great choice for kitchen, bath, or anywhere you want to create that perfect look.
- Mosaics Marble Thassos Hexagon - Ocean Blue
- A mix of Grey marble, Thassos marble and Blue Crystals in a 2x2 Hexagon mosaic
- ** Price is per Sheet (0.98 sq ft) ***
- Material: Thassos Marble
- Piece Size: 11.75" x 12"
- Individual Size: 2" x 2"
- Sq Ft Per Piece: 0.98
- Thickness: 3/8"
- Colors: Blue White and Grey
- Finish: Polished
- Use for Residential / Commercial, Interior Dry Walls, Interior Floors, Shower Walls, Shower Floors, Exterior Walls
- Installation Guide
- Installation Instructions
Recommended Substrates:
- Properly cured mortar beds-ANSI A108.1B (cured a minimum of 7 days).
- Cementitious backer units (CBU)-ANSI A118.9.
- Concrete slabs cured for 28 days minimum.
- Gypsum board (dry areas only)-ASTM C1396 or ASTM C1396M-04.
- Note: An ANSI A108A-2.1.8 membrane is required behind all CBU installations in wet areas.
- Note: All glass, foil backed glass, stainless steel and copper metal, aluminum, resin metal and blended element products must be set a minimum of 8"away from any naked flame.
Setting Materials and Methods:
- Setting material requirements will vary dependent upon the type of mosaic product being installed and the nature of the substrate.
- Advice on the appropriate setting materials should be sought from your tile and stone dealer at the time of purchase.
- Only use setting materials that meet or exceed TCNA guidelines
- Only use an accredited licensed contractor experienced in the art of installing mosaic products.
- Setting methods must conform to the TCNA guidelines.
Note: Grout Selection:
- The use of sanded and some premixed urethane micro glass bead enhanced grouts may cause damage to scratch sensitive surfaces. Always check with your Stone and Tile Dealer, Setting Contractor or Grout Manufacturer before selecting the grout type. Maniscalco is not responsible for any damage to the tile surface due to incorrect grout selection or incorrect grouting procedures.
- Colors may vary from picture, Product may have chips, pitting and other characteristics, Pictures are only an indication of color, texture and finish
Swimming Pool and Wet area Tiles
Color Stained glass tile mosaic
*** Price per Sheet (0.96 sq ft) ***
- Material: Glass
- Sheet Size: 11.75" x 11.75"
- Sq Ft Per Piece: 1.00
- Approximate Piece Size: 1" x 1"
- Thickness: 1/4"
- Colors: Pearl Blue
- Finish: Glossy
- Brighten up your pool or shower with this series of Handmade Porcelain mosaics.
- Pool rated and acceptable for use on shower walls.
- Use for Interior Dry Walls, Interior Floors, Shower Walls, Shower Floors, Pools, Pool Liners
- Installation Guide
Installation Instructions
Recommended Substrates:
- Properly cured mortar beds-ANSI A108.1B (cured a minimum of 7 days).
- Cementitious backer units (CBU)-ANSI A118.9.
- Concrete slabs cured for 28 days minimum.
- Gypsum board (dry areas only)-ASTM C1396 or ASTM C1396M-04.
- Note: An ANSI A108A-2.1.8 membrane is required behind all CBU installations in wet areas.
Setting Materials & Methods:
Setting material requirements will vary dependent upon the type of mosaic product being installed and the nature of the substrate.- Advice on the appropriate setting materials should be sought from your tile and stone dealer at the time of purchase.
- Only use setting materials that meet or exceed TCNA guidelines
- Only use an accredited licensed contractor experienced in the art of installing mosaic products.
- Setting methods must conform to the TCNA guidelines.
Note: Grout Selection:
The use of sanded and some premixed urethane micro glass bead enhanced grouts may cause damage to scratch sensitive surfaces. Always check with your Stone and Tile Dealer, Setting Contractor or Grout Manufacturer before selecting the grout type. Maniscalco is not responsible for any damage to the tile surface due to incorrect grout selection or incorrect grouting procedures.Colors may vary from picture, Product may have chips, pitting and other characteristics, Pictures are only an indication of color, texture and finish
- MOSAIC PORCELAIN PENNY ROUND - SKY BLUE
- Pool Rated for use in Swimming Pools
*** Price per Sheet ***
- Material: Handmade Porcelain
- Piece Size: 11.5"x12.25"
- Individual Size: 3/4"
- Sq Ft Per Piece: 0.98
- Thickness:.25"
- Colors: Mixed Blue Grey White
- Finish: Matte
For use in
- Pools, Pool Liners
- Interior Dry Walls
- Interior Floors
- Shower Walls, Shower Floors
- Exterior Walls
- Pool rated and acceptable for use on shower walls.
- The polyurethane cord backing makes installation easy.
- For use in Pools, Pool Liners, Shower Walls, Interior Dry Walls
- Installation Guide
Recommended Substrates:
- Properly cured mortar beds-ANSI A108.1B (cured a minimum of 7 days).
- Cementitious backer units (CBU)-ANSI A118.9.
- Concrete slabs cured for 28 days minimum.
- Gypsum board (dry areas only)-ASTM C1396 or ASTM C1396M-04.
- Note: An ANSI A108A-2.1.8 membrane is required behind all CBU installations in wet areas.
Setting Materials and Methods:
Setting material requirements will vary dependent upon the type of mosaic product being installed and the nature of the substrate.- Advice on the appropriate setting materials should be sought from your tile and stone dealer at the time of purchase.
- Only use setting materials that meet or exceed TCNA guidelines
- Only use an accredited licensed contractor experienced in the art of installing mosaic products.
- Setting methods must conform to the TCNA guidelines.
Acceptable Thin-Sets (White Color):
- MAPEI: Adesilex P10 Bright White Thin-Set Mortar mixed With Keraply Mortar Additive
- BOSTIK: Glass-Mate GLASS TILE MORTAR
- BOSTIK: ReFlex Ultra-Premium Latex Modified Thin-Set Mortar
- LATICRETE: Glass Tile Adhesive
- TEC SPECIALTY PRODUCTS: Super Flex Premium Performance Universal Latex-Modified ThinSet Mortar
Note: Grout Selection:
The use of sanded and some premixed urethane micro glass bead enhanced grouts may cause damage to scratch sensitive surfaces. Always check with your Stone and Tile Dealer, Setting Contractor or Grout Manufacturer before selecting the grout type. Maniscalco is not responsible for any damage to the tile surface due to incorrect grout selection or incorrect grouting procedures.Measuring: Measure coverage area, make sure to purchase at least 10% extra material than is required. This will account for any breakage or mis-cuts during installation, and ensure you have extra material should you have to replace any tile elements in the future.
Cutting: Plan the placement of the tiles on your wall prior to installation. If you need to cut a mosaic sheet, cut from the back using a utility knife between tiles along the grout joints. Should you need to cut across tiles in a fashion that is not possible with a utility knife, use a wet saw with a diamond blade to cut through the tile.
Drilling: Using a drill bit designed for glass is recommended. When drilling the hole, keep the bit and hole lubricated to prevent chipping. Start by drilling from both ends of the tile, starting with the back and drilling half the depth of the tile. Then, turn the tile over and complete the hole is recommended. This will prevent the glass from chipping as the drill bit exits the tile.
Applying Setting Materials:
Apply setting material using the notched side of a V-notched trowel. Using the flat side of the trowels, smooth out all ridges to achieve a consistent, even 1/8" (3mm) coverage.Apply glass mosaic sheets, mesh -side down, firmly into freshly laid setting material. Mix and match from assorted sell units to achieve consistent variation. Using a rubber grout float gently press the tile into adhesive to ensure complete contact.
Natural Stone should be sealed prior to grouting. A premium penetrating sealer is recommended for a natural look. Please refer to sealer manufacturer's recommendations for application instructions.
Cleaning: Clean all excess grout immediately with a damp sponge. After 12 hours polish off any remaining haze with a dry cloth or towel. For tough stains, we require the use of PH Neutral cleaner to clean the tile and grout, such as Grout and Tile neutral cleaner.
MAINTENANCE and CARE
Required to use a soft bristle brush to scrub the tile surfaces and grout. Take care to only use a soft bristle brush, to avoid the chance of scratching or damaging the grout. Then, simply wipe the surface, rinse well with clean water, and dry with a soft clean towel.
Required to use PH Neutral Cleaner to clean the tile and grout, such as Grout and Tile Neutral Cleaner
We strongly recommend customers to use a licensed tile contractor to do the tile installation and always use TCNA tile installation handbook as the installation guidance
Tile Maintenance and More
Colors may vary from picture, Product may have chips, pitting and other characteristics, Pictures are only an indication of color, texture and finish
- Marble and Glass in Pebble look - Ocean
- A blend of Thassos Marble with white glass in a Pebble layout style
- ** Price is per Sheet ***
- Material: Marble and Glass
- Sheet Size: 12" x 12" (1 sq ft per sheet)
- Thickness: 3/8"
- Colors: Blue White Grey
- Finish: Glossy
- Uses: Interior Dry Walls, Interior Floors (Residential), Shower Walls, Shower Floors (Residential)
- Installation Instructions
Recommended Substrates:
- Properly cured mortar beds-ANSI A108.1B (cured a minimum of 7 days).
- Cementitious backer units (CBU)-ANSI A118.9.
- Concrete slabs cured for 28 days minimum.
- Gypsum board (dry areas only)-ASTM C1396 or ASTM C1396M-04.
- Note: An ANSI A108A-2.1.8 membrane is required behind all CBU installations in wet areas.
- Note: All glass, foil backed glass, stainless steel and copper metal, aluminum, resin metal and blended element products must be set a minimum of 8"away from any naked flame.
- Measuring: Measure coverage area, make sure to purchase at least 10% extra material than is required. This will account for any breakage or mis-cuts during installation, and ensure you have extra material should you have to replace any tile elements in the future.
- Verifying Dye Lot Consistency: The owner or end user is responsible for determining the acceptability of the product. Due to the handmade, artistic nature of our product, variation in color, shade, tone, and size is normal.
- Upon delivery, open and inspect each box of tile.
- Verify dye lot consistency in the following manner. To establish color control samples, randomly select 5 pieces from your order from different boxes.
- To assure shade variations are acceptable check, the remaining sheets or field tile in your order against the control samples, prior to installation.
- If ordering additional materials. Sample shall be sent to help attempt to match previously ordered material.
- Setting Material: Because of the translucent nature of glass, the color of the bonding material will impact the ultimate look of the tile. We highly recommend the use of white polymer modified white thin-set.
Acceptable Thin-Sets (White Color):
- MAPEI: Adesilex P10 Bright White Thin-Set Mortar mixed With Keraply Mortar Additive
- BOSTIK: Glass-Mate™ GLASS TILE MORTAR
- BOSTIK: ReFlex Ultra-Premium Latex Modified Thin-Set Mortar
- LATICRETE: Glass Tile Adhesive
- TEC SPECIALTY PRODUCTS: Super Flex Premium Performance Universal Latex-Modified ThinSet Mortar
Acceptable Grout:
- MAPEI: Keracolor S
- Bostik: Dimensions and TruColor
- LATICRETE: 1500 Sanded Grout
- TEC: AccuColor Premium Sanded Tile Grout
- Cutting: Plan the placement of the tiles on your wall prior to installation. If you need to cut a mosaic sheet, cut from the back using a utility knife between tiles along the grout joints. Should you need to cut across tiles in a fashion that is not possible with a utility knife, use a wet saw with a diamond blade to cut through the tile.
- Drilling: Using a drill bit designed for glass is recommended. When drilling the hole, keep the bit and hole lubricated to prevent chipping. Start by drilling from both ends of the tile, starting with the back and drilling half the depth of the tile. Then, turn the tile over and complete the hole is recommended. This will prevent the glass from chipping as the drill bit exits the tile.
Applying Setting Materials:
Apply setting material using the notched side of a V-notched trowel. Using the flat side of the trowels, smooth out all ridges to achieve a consistent, even 1/8" (3mm) coverage.Apply glass mosaic sheets, mesh -side down, firmly into freshly laid setting material. Mix and match from assorted sell units to achieve consistent variation. Using a rubber grout float gently press the tile into adhesive to ensure complete contact.
Natural Stone should be sealed prior to grouting. A premium penetrating sealer is recommended for a natural look. Please refer to sealer manufacturer's recommendations for application instructions.
- Cleaning: Clean all excess grout immediately with a damp sponge. After 12 hours polish off any remaining haze with a dry cloth or towel. For tough stains, we require the use of PH Neutral cleaner to clean the tile and grout, such as Grout and Tile neutral cleaner.
- Maintenance and Care
We strongly recommend customers to use a licensed tile contractor to do the tile installation and always use TCNA tile installation handbook as the installation guidance
- Colors may vary from picture, Product may have chips, pitting and other characteristics, Pictures are only an indication of color, texture and finish
- Size: 11.02 x 11.02 inch;
- Thickness: 5/16 inch;
- Finish: Polished (Glossy);
Colors:
- Tan - Tan Beige & Light Brown Broken Glass with Rainbow Round Glass Inserts.
- Blue Laguna - Blue Irregular Broken Glass in Light Blue Color
- Royal - Blue , Tan Irregular Broken Glass in Light Blue Color
- Light Grey - Grey Irregular Broken Glass in White & Light Grey Color.
- Material: Glass
- Sheet Size: 11" x 11 1/2"
- SqFt Per Piece: 0.88
- Thickness: 3/8"
- Finish: Glossy
- Interior Dry Walls, Shower Walls, Residential, Commercial, Light Commercial
- Installation Guide
Installation Instructions
Recommended Substrates:
- Properly cured mortar beds-ANSI A108.1B (cured a minimum of 7 days).
- Cementitious backer units (CBU)-ANSI A118.9.
- Concrete slabs cured for 28 days minimum.
- Gypsum board (dry areas only)-ASTM C1396 or ASTM C1396M-04.
- Note: An ANSI A108A-2.1.8 membrane is required behind all CBU installations in wet areas.
Setting Materials & Methods:
Setting material requirements will vary dependent upon the type of mosaic product being installed and the nature of the substrate.- Advice on the appropriate setting materials should be sought from your tile and stone dealer at the time of purchase.
- Only use setting materials that meet or exceed TCNA guidelines
- Only use an accredited licensed contractor experienced in the art of installing mosaic products.
- Setting methods must conform to the TCNA guidelines.
- Do not cover/protect the Victoria Metals with adhesive tape of any kind.
Note: Grout Selection:
The use of sanded and some premixed urethane micro glass bead enhanced grouts may cause damage to scratch sensitive surfaces. Always check with your Stone and Tile Dealer, Setting Contractor or Grout Manufacturer before selecting the grout type. Maniscalco is not responsible for any damage to the tile surface due to incorrect grout selection or incorrect grouting procedures.Sealing Guide:
- Sealing prior to grouting is recommended for all stone mosaics.
- Glass (see note below), Stainless Steel, Antique Copper and Aluminum mosaics do not require sealing.
- Note: Pre sealing prior to setting is necessary when installing Barossa Valley Crystal Glass.
- Note: Only use water based sealers with Sydney Harbor Metals.
- Note: When sealing Botany Bay pebbles expect some darkening of the color. Test sealer on a sample area first.
- Tile Maintenance and More
- Size: 2 x 2 inch pieces mounted on 12 x 12 (1 sq. ft.) sturdy mesh tile sheet6 rows and 6 columns with 36 stones per sheet1/16 inch grout width;
- Thickness: 5/16 inch;
- Finish: Honed (Matte);
Swimming Pool and Wet area Tiles
Color Stained glass tile mosaic
*** Price is per Sheet (0.96 sq ft) ***
- Material: Glass
- Sheet Size: 11.75" x 11.75"
- Sq Ft Per Piece: 1.00
- Approximate Piece Size: 1" x 1"
- Thickness: 1/4"
- Colors: Sky Blue
- Finish: Glossy
- Brighten up your pool or shower with this series of Handmade Porcelain mosaics.
- Pool rated and acceptable for use on shower walls.
- Use for Interior Dry Walls, Interior Floors, Shower Walls, Shower Floors, Pools, Pool Liners
- Installation Guide
Installation Instructions
Recommended Substrates:
- Properly cured mortar beds-ANSI A108.1B (cured a minimum of 7 days).
- Cementitious backer units (CBU)-ANSI A118.9.
- Concrete slabs cured for 28 days minimum.
- Gypsum board (dry areas only)-ASTM C1396 or ASTM C1396M-04.
- Note: An ANSI A108A-2.1.8 membrane is required behind all CBU installations in wet areas.
Setting Materials & Methods:
Setting material requirements will vary dependent upon the type of mosaic product being installed and the nature of the substrate.- Advice on the appropriate setting materials should be sought from your tile and stone dealer at the time of purchase.
- Only use setting materials that meet or exceed TCNA guidelines
- Only use an accredited licensed contractor experienced in the art of installing mosaic products.
- Setting methods must conform to the TCNA guidelines.
Note: Grout Selection:
The use of sanded and some premixed urethane micro glass bead enhanced grouts may cause damage to scratch sensitive surfaces. Always check with your Stone and Tile Dealer, Setting Contractor or Grout Manufacturer before selecting the grout type. Maniscalco is not responsible for any damage to the tile surface due to incorrect grout selection or incorrect grouting procedures.Colors may vary from picture, Product may have chips, pitting and other characteristics, Pictures are only an indication of color, texture and finish
- Marble and Glass in Pebble look - Blue
- A blend of Marble with white glass in a Pebble layout style
- ** Price is per Sheet ***
- Material: Marble and Glass
- Sheet Size: 12" x 12" (1 sq ft per sheet)
- Thickness: 3/8"
- Colors: White, Blue and Grey
- Finish: Glossy
- Uses: Interior Dry Walls, Interior Floors (Residential), Shower Walls, Shower Floors (Residential)
- Installation Instructions
Recommended Substrates:
- Properly cured mortar beds-ANSI A108.1B (cured a minimum of 7 days).
- Cementitious backer units (CBU)-ANSI A118.9.
- Concrete slabs cured for 28 days minimum.
- Gypsum board (dry areas only)-ASTM C1396 or ASTM C1396M-04.
- Note: An ANSI A108A-2.1.8 membrane is required behind all CBU installations in wet areas.
- Note: All glass, foil backed glass, stainless steel and copper metal, aluminum, resin metal and blended element products must be set a minimum of 8"away from any naked flame.
- Measuring: Measure coverage area, make sure to purchase at least 10% extra material than is required. This will account for any breakage or mis-cuts during installation, and ensure you have extra material should you have to replace any tile elements in the future.
- Verifying Dye Lot Consistency: The owner or end user is responsible for determining the acceptability of the product. Due to the handmade, artistic nature of our product, variation in color, shade, tone, and size is normal.
- Upon delivery, open and inspect each box of tile.
- Verify dye lot consistency in the following manner. To establish color control samples, randomly select 5 pieces from your order from different boxes.
- To assure shade variations are acceptable check, the remaining sheets or field tile in your order against the control samples, prior to installation.
- If ordering additional materials. Sample shall be sent to help attempt to match previously ordered material.
- Setting Material: Because of the translucent nature of glass, the color of the bonding material will impact the ultimate look of the tile. We highly recommend the use of white polymer modified white thin-set.
Acceptable Thin-Sets (White Color):
- MAPEI: Adesilex P10 Bright White Thin-Set Mortar mixed With Keraply Mortar Additive
- BOSTIK: Glass-Mate™ GLASS TILE MORTAR
- BOSTIK: ReFlex Ultra-Premium Latex Modified Thin-Set Mortar
- LATICRETE: Glass Tile Adhesive
- TEC SPECIALTY PRODUCTS: Super Flex Premium Performance Universal Latex-Modified ThinSet Mortar
Acceptable Grout:
- MAPEI: Keracolor S
- Bostik: Dimensions and TruColor
- LATICRETE: 1500 Sanded Grout
- TEC: AccuColor Premium Sanded Tile Grout
- Cutting: Plan the placement of the tiles on your wall prior to installation. If you need to cut a mosaic sheet, cut from the back using a utility knife between tiles along the grout joints. Should you need to cut across tiles in a fashion that is not possible with a utility knife, use a wet saw with a diamond blade to cut through the tile.
- Drilling: Using a drill bit designed for glass is recommended. When drilling the hole, keep the bit and hole lubricated to prevent chipping. Start by drilling from both ends of the tile, starting with the back and drilling half the depth of the tile. Then, turn the tile over and complete the hole is recommended. This will prevent the glass from chipping as the drill bit exits the tile.
Applying Setting Materials:
Apply setting material using the notched side of a V-notched trowel. Using the flat side of the trowels, smooth out all ridges to achieve a consistent, even 1/8" (3mm) coverage.Apply glass mosaic sheets, mesh -side down, firmly into freshly laid setting material. Mix and match from assorted sell units to achieve consistent variation. Using a rubber grout float gently press the tile into adhesive to ensure complete contact.
Natural Stone should be sealed prior to grouting. A premium penetrating sealer is recommended for a natural look. Please refer to sealer manufacturer's recommendations for application instructions.
- Cleaning: Clean all excess grout immediately with a damp sponge. After 12 hours polish off any remaining haze with a dry cloth or towel. For tough stains, we require the use of PH Neutral cleaner to clean the tile and grout, such as Grout and Tile neutral cleaner.
- Maintenance and Care
We strongly recommend customers to use a licensed tile contractor to do the tile installation and always use TCNA tile installation handbook as the installation guidance
- Colors may vary from picture, Product may have chips, pitting and other characteristics, Pictures are only an indication of color, texture and finish
Design Type:
- Design Type: Polished Finish
Design:
- Color: Carrara White
- Material Type:Marble
- We sell by: Sheet
- Width: 12 Height: 12 Thickness:0.38
- Chip Size (If available)
- Application: Bathroom, Bedroom, Kitchen indoor, and outdoor tiles.
- Product Code:Fancy_group_1293
- Product Code: Fancy_group_1293
- Sold By Unit: Box
- Coverage Area: 10 FT (square-feet)
- Number of Pieces included in 1 Quantity: 10
- Code: Fancyoption_4741
- 1 Sq Ft: $29.99
- 4" x 6" Sample: $6.99
- Weight: 3.7 LBS/ Sq Ft
- Individual Tile Pieces: 1 inch circles
- Sheet Size: 11" x 12"
- Thickness: 8 mm
Design Type:
- Design Type: Polished Finish
Design:
- Color: Carrara White
- Material Type:Marble
- We sell by: Sheet
- Width: 12 Height: 12 Thickness:0.38
- Chip Size (If available)
- Application: Bathroom, Bedroom, Kitchen indoor, and outdoor tiles.
- Product Code:Fancy_group_1263
- Product Code: Fancy_group_1263
- Sold By Unit: Box
- Coverage Area: 10 FT (square-feet)
- Number of Pieces included in 1 Quantity: 10
- Code: Fancyoption_4711