- All Products
- Bath
- Tile
- Mosaic Tile
- Finish: Glossy
Contemporary Colorful Glossy Mosaic Tile
- 10.5 square feet, 10 pieces per case. Case weight is 18.02 lbs.
- Grade 1, first-quality porcelain tile for floor and wall use
- 11.88 in. width x 12.63 in. length x 0.21 in. thick mesh-mounted mosaic
- Glazed, smooth finish with a high sheen and uniform appearance in tone
- PEI Rating IV has high resistance to abrasion and is suitable for heavy-duty residential and commercial kitchens, hotels, exhibition and sales rooms with some dirt conditions
- Impervious tiles have a water absorption of less than 0.5% for indoor and outdoor use and are frost resistant
- This tile is not ADA approved for slip resistance with a DCOF value less than 0.42.
- Completely frost resistant for indoor or outdoor applications; use a latex-modified thinset for acceptable bond strength
- WARNING: Silica dust is harmful if inhaled. Exposure to silica dust from cutting, grinding, or polishing can cause acute lung injury, silicosis or cancer. Wear a respirator when cutting, grinding, or polishing. Use wet cutting methods and do not dry cut. Children should not be present during cutting, grinding or polishing.
- Country of Origin: Indonesia
- 10.6 square feet, 10 pieces per case. Case weight is 17.58 lbs.
- Grade 1, first-quality porcelain tile for floor and wall use
- 12.25 in. width x 12.25 in. length x 0.25 in. thick mesh-mounted mosaic
- Glazed, smooth finish with a high sheen and moderate variation in tone
- PEI Rating II is suitable for all interior walls and light foot traffic such as powder rooms
- Impervious tiles have a water absorption of less than 0.5% for indoor and outdoor use and are frost resistant
- This tile has a COF wet rating less than or equal to 0.50 and is considered to have a marginally low skid resistance. This tile is not ADA approved for slip resistance.
- Completely frost resistant for indoor or outdoor applications; use a latex-modified thinset for acceptable bond strength
- WARNING: Silica dust is harmful if inhaled. Exposure to silica dust from cutting, grinding, or polishing can cause acute lung injury, silicosis or cancer. Wear a respirator when cutting, grinding, or polishing. Use wet cutting methods and do not dry cut. Children should not be present during cutting, grinding or polishing.
- Country of Origin: Indonesia
- 11.2 square feet, 10 pieces per case. Case weight is 19 lbs.
- Grade 1, first-quality porcelain tile for floor and wall use
- 11.88 in. width x 13.25 in. length x 0.19 in. thick mesh-mounted mosaic
- Glazed, smooth finish with a high sheen and slight variation in tone
- PEI Rating IV has high resistance to abrasion and is suitable for heavy-duty residential and commercial kitchens, hotels, exhibition and sales rooms with some dirt conditions
- Impervious tiles have a water absorption of less than 0.5% for indoor and outdoor use and are frost resistant
- This tile is not ADA approved for slip resistance with a DCOF value less than 0.42.
- Completely frost resistant for indoor or outdoor applications; use a latex-modified thinset for acceptable bond strength
- WARNING: Silica dust is harmful if inhaled. Exposure to silica dust from cutting, grinding, or polishing can cause acute lung injury, silicosis or cancer. Wear a respirator when cutting, grinding, or polishing. Use wet cutting methods and do not dry cut. Children should not be present during cutting, grinding or polishing.
- Country of Origin: Indonesia
- Price is per sheet
- Dimension: 12" x 12 Sheet
- Thickness: 5mm
- Surface: Glossy Glazed
- Material: Porcelain
- Application: Wall & Floor
- 10.1 square feet, 10 pieces per case. Case weight is 20.6 lbs.
- Grade 1, first-quality porcelain tile for floor and wall use
- 11.88 in. width x 11.88 in. length x 0.26 in. thick mesh-mounted mosaic
- Glazed, smooth finish with a high sheen and moderate variation in tone
- PEI Rating II is suitable for all interior walls and light foot traffic such as powder rooms
- Impervious tiles have a water absorption of less than 0.5% for indoor and outdoor use and are frost resistant
- This tile is not ADA approved for slip resistance with a DCOF value less than 0.42.
- Completely frost resistant for indoor or outdoor applications; use a latex-modified thinset for acceptable bond strength
- WARNING: Silica dust is harmful if inhaled. Exposure to silica dust from cutting, grinding, or polishing can cause acute lung injury, silicosis or cancer. Wear a respirator when cutting, grinding, or polishing. Use wet cutting methods and do not dry cut. Children should not be present during cutting, grinding or polishing.
- Country of Origin: Indonesia
- 11.2 square feet, 10 pieces per case. Case weight is 19 lbs.
- Grade 1, first-quality porcelain tile for floor and wall use
- 11.88 in. width x 13.25 in. length x 0.19 in. thick mesh-mounted mosaic
- Glazed, smooth finish with a high sheen and slight variation in tone
- PEI Rating II is suitable for all interior walls and light foot traffic such as powder rooms
- Impervious tiles have a water absorption of less than 0.5% for indoor and outdoor use and are frost resistant
- This tile is not ADA approved for slip resistance with a DCOF value less than 0.42.
- Completely frost resistant for indoor or outdoor applications; use a latex-modified thinset for acceptable bond strength
- WARNING: Silica dust is harmful if inhaled. Exposure to silica dust from cutting, grinding, or polishing can cause acute lung injury, silicosis or cancer. Wear a respirator when cutting, grinding, or polishing. Use wet cutting methods and do not dry cut. Children should not be present during cutting, grinding or polishing.
- Country of Origin: Indonesia
- 1.06 square feet per piece, each piece sold individually. Piece weight equals 2.2 lbs.
- Grade 1, first-quality porcelain tile for floor and wall use
- 12 in. width x 12.5 in. length x 0.25 in. thick mesh-mounted mosaic
- Glazed, smooth finish with a high sheen and moderate variation in tone
- PEI Rating I is suitable for light-duty residential floors, bathrooms and bedrooms without direct access from outside; no scratching dirt can be present
- Impervious tiles have a water absorption of less than 0.5% for indoor and outdoor use and are frost resistant
- This tile is not ADA approved for slip resistance with a DCOF value less than 0.42.
- Completely frost resistant for indoor or outdoor applications; use a latex-modified thinset for acceptable bond strength
- WARNING: Silica dust is harmful if inhaled. Exposure to silica dust from cutting, grinding, or polishing can cause acute lung injury, silicosis or cancer. Wear a respirator when cutting, grinding, or polishing. Use wet cutting methods and do not dry cut. Children should not be present during cutting, grinding or polishing.
- Country of Origin: Japan
- 10.5 square feet, 10 pieces per case. Case weight is 17.5 lbs.
- Grade 1, first-quality porcelain tile for floor and wall use
- 11.88 in. width x 12.63 in. length x 0.21 in. thick mesh-mounted mosaic
- Glazed, smooth finish with a high sheen and slight variation in tone
- PEI Rating II is suitable for all interior walls and light foot traffic such as powder rooms
- Impervious tiles have a water absorption of less than 0.5% for indoor and outdoor use and are frost resistant
- This tile is not ADA approved for slip resistance with a DCOF value less than 0.42.
- Completely frost resistant for indoor or outdoor applications; use a latex-modified thinset for acceptable bond strength
- WARNING: Silica dust is harmful if inhaled. Exposure to silica dust from cutting, grinding, or polishing can cause acute lung injury, silicosis or cancer. Wear a respirator when cutting, grinding, or polishing. Use wet cutting methods and do not dry cut. Children should not be present during cutting, grinding or polishing.
- Country of Origin: Indonesia
This porcelain mosaic tile from The Mosaic Factory is sophisticated, stylish, and suitable for any wall application, including but not limited to kitchen backsplashes, bathrooms, fireplaces, and pools. Sheets of tile are backed on mesh for easy installation. Glossy tiles can also be installed on bathroom floors (not shower floors) and other low traffic residential area's. Matte tiles can also be used on residential shower floors. Slip resistant tiles (The Mosaic Factory London series) can also be used in commercial high traffic areas like entrances, restrooms, and kitchen floors. The tiles can also be peeled off the mesh and installed individually, mixed with other colors.
Product Specifications
- Color: Light Green
- Material: Porcelain
- Surface: Glossy
- Individual tile size (WxH): 3.6"x 0.47"
- Sheet size (WxH): 11.1"x 12.1" (0.94 sq. ft.)
- Thickness: 8 mm
- Grout joint: 2.5 mm
- Sheet backing: Mesh - ready for installation
- Impervious to liquids and vapors
- Resistant to fading, staining, and discoloration
- Shade variation: V1 - Uniform Appearance
- PEI rating: PEI 2 - Light Traffic
- Sample
- It is highly recommended to order a sample. Order multiple samples of the same product if it is a product with high shade variation. Sample is a cut piece of a sheet for color and texture reference. Samples are non returnable and non refundable.
- When measuring your project and ordering the product quantity make sure you order at least 10% extra for cuts, trimming, damaged pieces, and future repairs The installation is similar to the installation of wall tiles.
- Shipping and order quantity
- Due to the delicate nature of this tile, this item is only available for shipment on a pallet with a freight carrier.
- Therefore this item can only be ordered per increments of 60 sheets (6 boxes).
V1 - Uniform Appearance - Differences among pieces from the same production run are minimal V2 - Slight Variation - Clearly distinguishable differences in texture and/or pattern within similar colors V3 - Moderate Variation - While the colors present on a single piece of tile will be indicative of the colors to be expected on the other tiles, the amount of colors on each piece may vary significantly. For example 'that little bit of color' on one piece of tile may be the primary color on the next pieces. V4 - Substantial Variation - Random color differences from tile to tile, so that one tile may have totally different colors from that of other tiles. Thus the final installation will be unique.
PEI Rating
PEI is a measurement of the “abrasion resistance” of a tile, meaning how much “rubbing” does it take to physically impact the look of the tile. The test is scored on a scale and each value represents a durability to withstand increasingly more demanding traffic. PEI 1, Very Light Traffic - These tiles can be used on all indoor wall applications, for countertops such as bathrooms, and very light traffic residential bathroom floors. These tiles are not recommended for any area that will have any constant or heavy floor traffic. We do not recommend these to be used on floors at all. PEI 2, Light Traffic - These tiles can be used on all indoor wall applications, interior countertops applications and light traffic residential bathroom floors. These tiles should not be used in areas such as kitchens, entry ways, stairs or areas with heavy traffic. We recommend these only to be used on floors were you would normally walk barefoot / without shoes.
This porcelain mosaic tile from The Mosaic Factory is sophisticated, stylish, and suitable for any wall application, including but not limited to kitchen backsplashes, bathrooms, fireplaces, and pools. Sheets of tile are backed on mesh for easy installation. Glossy tiles can also be installed on bathroom floors (not shower floors) and other low traffic residential area's. Matte tiles can also be used on residential shower floors. Slip resistant tiles (The Mosaic Factory London series) can also be used in commercial high traffic areas like entrances, restrooms, and kitchen floors. The tiles can also be peeled off the mesh and installed individually, mixed with other colors.
Product Specifications
- Color: Ocean Green
- Material: Porcelain
- Surface: Glossy
- Individual tile size (WxH): 5.7"x 0.8"
- Sheet size (WxH): 11.7"x 11.8" (0.95 sq. ft.)
- Thickness: 8 mm
- Grout joint: 3.5 mm
- Sheet backing: Mesh - ready for installation
- Impervious to liquids and vapors
- Resistant to fading, staining, and discoloration
- Shade variation: V1 - Uniform Appearance
- PEI rating: PEI 2 - Light Traffic
- Sample
- It is highly recommended to order a sample. Order multiple samples of the same product if it is a product with high shade variation. Sample is a cut piece of a sheet for color and texture reference. Samples are non returnable and non refundable.
- When measuring your project and ordering the product quantity make sure you order at least 10% extra for cuts, trimming, damaged pieces, and future repairs The installation is similar to the installation of wall tiles.
- Shipping and order quantity
- Due to the delicate nature of this tile, this item is only available for shipment on a pallet with a freight carrier.
- Therefore this item can only be ordered per increments of 60 sheets (6 boxes).
V1 - Uniform Appearance - Differences among pieces from the same production run are minimal V2 - Slight Variation - Clearly distinguishable differences in texture and/or pattern within similar colors V3 - Moderate Variation - While the colors present on a single piece of tile will be indicative of the colors to be expected on the other tiles, the amount of colors on each piece may vary significantly. For example 'that little bit of color' on one piece of tile may be the primary color on the next pieces. V4 - Substantial Variation - Random color differences from tile to tile, so that one tile may have totally different colors from that of other tiles. Thus the final installation will be unique.
PEI Rating
PEI is a measurement of the “abrasion resistance” of a tile, meaning how much “rubbing” does it take to physically impact the look of the tile. The test is scored on a scale and each value represents a durability to withstand increasingly more demanding traffic. PEI 1, Very Light Traffic - These tiles can be used on all indoor wall applications, for countertops such as bathrooms, and very light traffic residential bathroom floors. These tiles are not recommended for any area that will have any constant or heavy floor traffic. We do not recommend these to be used on floors at all. PEI 2, Light Traffic - These tiles can be used on all indoor wall applications, interior countertops applications and light traffic residential bathroom floors. These tiles should not be used in areas such as kitchens, entry ways, stairs or areas with heavy traffic. We recommend these only to be used on floors were you would normally walk barefoot / without shoes.
This porcelain mosaic tile from The Mosaic Factory is sophisticated, stylish, and suitable for any wall application, including but not limited to kitchen backsplashes, bathrooms, fireplaces, and pools. Sheets of tile are backed on mesh for easy installation. Glossy tiles can also be installed on bathroom floors (not shower floors) and other low traffic residential area's. Matte tiles can also be used on residential shower floors. Slip resistant tiles (The Mosaic Factory London series) can also be used in commercial high traffic areas like entrances, restrooms, and kitchen floors. The tiles can also be peeled off the mesh and installed individually, mixed with other colors.
Product Specifications
- Color: Turquoise
- Material: Porcelain
- Surface: Glossy
- Individual tile size (WxH): 5.7"x 0.8"
- Sheet size (WxH): 11.7"x 11.8" (0.95 sq. ft.)
- Thickness: 8 mm
- Grout joint: 3.5 mm
- Sheet backing: Mesh - ready for installation
- Impervious to liquids and vapors
- Resistant to fading, staining, and discoloration
- Shade variation: V1 - Uniform Appearance
- PEI rating: PEI 2 - Light Traffic
- Sample
- It is highly recommended to order a sample. Order multiple samples of the same product if it is a product with high shade variation. Sample is a cut piece of a sheet for color and texture reference. Samples are non returnable and non refundable.
- When measuring your project and ordering the product quantity make sure you order at least 10% extra for cuts, trimming, damaged pieces, and future repairs The installation is similar to the installation of wall tiles.
- Shipping and order quantity
- Due to the delicate nature of this tile, this item is only available for shipment on a pallet with a freight carrier.
- Therefore this item can only be ordered per increments of 60 sheets (6 boxes).
V1 - Uniform Appearance - Differences among pieces from the same production run are minimal V2 - Slight Variation - Clearly distinguishable differences in texture and/or pattern within similar colors V3 - Moderate Variation - While the colors present on a single piece of tile will be indicative of the colors to be expected on the other tiles, the amount of colors on each piece may vary significantly. For example 'that little bit of color' on one piece of tile may be the primary color on the next pieces. V4 - Substantial Variation - Random color differences from tile to tile, so that one tile may have totally different colors from that of other tiles. Thus the final installation will be unique.
PEI Rating
PEI is a measurement of the “abrasion resistance” of a tile, meaning how much “rubbing” does it take to physically impact the look of the tile. The test is scored on a scale and each value represents a durability to withstand increasingly more demanding traffic. PEI 1, Very Light Traffic - These tiles can be used on all indoor wall applications, for countertops such as bathrooms, and very light traffic residential bathroom floors. These tiles are not recommended for any area that will have any constant or heavy floor traffic. We do not recommend these to be used on floors at all. PEI 2, Light Traffic - These tiles can be used on all indoor wall applications, interior countertops applications and light traffic residential bathroom floors. These tiles should not be used in areas such as kitchens, entry ways, stairs or areas with heavy traffic. We recommend these only to be used on floors were you would normally walk barefoot / without shoes.
Pool Rated for use in Swimming Pools
** Price is per Piece **
- Material: Handmade Porcelain
- Piece Size: 11 1/2" x 11 1/2"
- Sq Ft Per Piece: 0.92
- Thickness: 1/4"
- Color: Royal Blue
- Finish: Glossy
For use in
- Pools, Pool Liners
- Interior Dry Walls
- Interior Floors
- Shower Walls, Shower Floors
- Exterior Walls, Exterior Floors
- Pool rated and acceptable for use on shower walls.
- The polyurethane cord backing makes installation easy.
- For use in Pools, Pool Liners, Shower Walls, Interior Dry Walls
- Installation Guide
Recommended Substrates:
- Properly cured mortar beds-ANSI A108.1B (cured a minimum of 7 days).
- Cementitious backer units (CBU)-ANSI A118.9.
- Concrete slabs cured for 28 days minimum.
- Gypsum board (dry areas only)-ASTM C1396 or ASTM C1396M-04.
- Note: An ANSI A108A-2.1.8 membrane is required behind all CBU installations in wet areas.
Setting Materials & Methods:
Setting material requirements will vary dependent upon the type of mosaic product being installed and the nature of the substrate.- Advice on the appropriate setting materials should be sought from your tile and stone dealer at the time of purchase.
- Only use setting materials that meet or exceed TCNA guidelines
- Only use an accredited licensed contractor experienced in the art of installing mosaic products.
- Setting methods must conform to the TCNA guidelines.
Acceptable Thin-Sets (White Color):
- MAPEI: Adesilex P10 Bright White Thin-Set Mortar mixed With Keraply Mortar Additive
- BOSTIK: Glass-Mate™ GLASS TILE MORTAR
- BOSTIK: ReFlex Ultra-Premium Latex Modified Thin-Set Mortar
- LATICRETE: Glass Tile Adhesive
- TEC SPECIALTY PRODUCTS: Super Flex Premium Performance Universal Latex-Modified ThinSet Mortar
Note: Grout Selection:
The use of sanded and some premixed urethane micro glass bead enhanced grouts may cause damage to scratch sensitive surfaces. Always check with your Stone and Tile Dealer, Setting Contractor or Grout Manufacturer before selecting the grout type. Maniscalco is not responsible for any damage to the tile surface due to incorrect grout selection or incorrect grouting procedures.Measuring: Measure coverage area, make sure to purchase at least 10% extra material than is required. This will account for any breakage or mis-cuts during installation, and ensure you have extra material should you have to replace any tile elements in the future.
Cutting: Plan the placement of the tiles on your wall prior to installation. If you need to cut a mosaic sheet, cut from the back using a utility knife between tiles along the grout joints. Should you need to cut across tiles in a fashion that is not possible with a utility knife, use a wet saw with a diamond blade to cut through the tile.
Drilling: Using a drill bit designed for glass is recommended. When drilling the hole, keep the bit and hole lubricated to prevent chipping. Start by drilling from both ends of the tile, starting with the back and drilling half the depth of the tile. Then, turn the tile over and complete the hole is recommended. This will prevent the glass from chipping as the drill bit exits the tile.
Applying Setting Materials:
Apply setting material using the notched side of a V-notched trowel. Using the flat side of the trowels, smooth out all ridges to achieve a consistent, even 1/8” (3mm) coverage.Apply glass mosaic sheets, mesh -side down, firmly into freshly laid setting material. Mix and match from assorted sell units to achieve consistent variation. Using a rubber grout float gently press the tile into adhesive to ensure complete contact.
Natural Stone should be sealed prior to grouting. A premium penetrating sealer is recommended for a natural look. Please refer to sealer manufacturer’s recommendations for application instructions.
Cleaning: Clean all excess grout immediately with a damp sponge. After 12 hours polish off any remaining haze with a dry cloth or towel. For tough stains, we require the use of PH Neutral cleaner to clean the tile and grout, such as Grout & Tile neutral cleaner.
MAINTENANCE & CARE
Required to use a soft bristle brush to scrub the tile surfaces and grout. Take care to only use a soft bristle brush, to avoid the chance of scratching or damaging the grout. Then, simply wipe the surface, rinse well with clean water, and dry with a soft clean towel.
Required to use PH Neutral Cleaner to clean the tile and grout, such as Grout & Tile Neutral Cleaner
We strongly recommend customers to use a licensed tile contractor to do the tile installation and always use TCNA tile installation handbook as the installation guidance
Tile Maintenance and More
Colors may vary from picture, Product may have chips, pitting and other characteristics, Pictures are only an indication of color, texture and finish
- 10.6 square feet, 10 pieces per case. Case weight is 17 lbs.
- Grade 1, first-quality porcelain tile for floor and wall use
- 12.25 in. width x 12.25 in. length x 0.25 in. thick mesh-mounted mosaic
- Glazed, smooth finish with a high sheen and uniform appearance in tone
- PEI Rating IV has high resistance to abrasion and is suitable for heavy-duty residential and commercial kitchens, hotels, exhibition and sales rooms with some dirt conditions
- Impervious tiles have a water absorption of less than 0.5% for indoor and outdoor use and are frost resistant
- This tile has a COF wet rating less than or equal to 0.50 and is considered to have a marginally low skid resistance. This tile is not ADA approved for slip resistance.
- Completely frost resistant for indoor or outdoor applications; use a latex-modified thinset for acceptable bond strength
- WARNING: Silica dust is harmful if inhaled. Exposure to silica dust from cutting, grinding, or polishing can cause acute lung injury, silicosis or cancer. Wear a respirator when cutting, grinding, or polishing. Use wet cutting methods and do not dry cut. Children should not be present during cutting, grinding or polishing.
- Country of Origin: Indonesia
- MOSAIC GLASS TILE SURFACE WAVES - LIGHT GREEN
- Pool Rated for use in Swimming Pools
Water jet light green glass piece precisely cut to create perfect wave-like pattern.
- Material: Glass
- Piece Size: 11 1/2" x 12 1/2"
- Sq Ft Per Piece: 1
- Thickness: 3/8"
- Colors: Light Green
- Finish: Glossy
- Brighten up your pool or shower with this series
- Pool rated and acceptable for use on shower walls.
- The polyurethane cord backing makes installation easy.
- For use in Shower Walls, Shower Floors, Pools, Pool Liners, Interior Dry Walls, Interior Floors, Exterior Walls
- Installation Guide
Recommended Substrates:
- Properly cured mortar beds-ANSI A108.1B (cured a minimum of 7 days).
- Cementitious backer units (CBU)-ANSI A118.9.
- Concrete slabs cured for 28 days minimum.
- Gypsum board (dry areas only)-ASTM C1396 or ASTM C1396M-04.
- Note: An ANSI A108A-2.1.8 membrane is required behind all CBU installations in wet areas.
Setting Materials & Methods:
Setting material requirements will vary dependent upon the type of mosaic product being installed and the nature of the substrate.- Advice on the appropriate setting materials should be sought from your tile and stone dealer at the time of purchase.
- Only use setting materials that meet or exceed TCNA guidelines
- Only use an accredited licensed contractor experienced in the art of installing mosaic products.
- Setting methods must conform to the TCNA guidelines.
Note: Grout Selection:
The use of sanded and some premixed urethane micro glass bead enhanced grouts may cause damage to scratch sensitive surfaces. Always check with your Stone and Tile Dealer, Setting Contractor or Grout Manufacturer before selecting the grout type. Maniscalco is not responsible for any damage to the tile surface due to incorrect grout selection or incorrect grouting procedures.Measuring: Measure coverage area, make sure to purchase at least 10% extra material than is required. This will account for any breakage or mis-cuts during installation, and ensure you have extra material should you have to replace any tile elements in the future.
Cutting: Plan the placement of the tiles on your wall prior to installation. If you need to cut a mosaic sheet, cut from the back using a utility knife between tiles along the grout joints. Should you need to cut across tiles in a fashion that is not possible with a utility knife, use a wet saw with a diamond blade to cut through the tile.
Drilling: Using a drill bit designed for glass is recommended. When drilling the hole, keep the bit and hole lubricated to prevent chipping. Start by drilling from both ends of the tile, starting with the back and drilling half the depth of the tile. Then, turn the tile over and complete the hole is recommended. This will prevent the glass from chipping as the drill bit exits the tile.
Applying Setting Materials:
Apply setting material using the notched side of a V-notched trowel. Using the flat side of the trowels, smooth out all ridges to achieve a consistent, even 1/8” (3mm) coverage.Apply glass mosaic sheets, mesh -side down, firmly into freshly laid setting material. Mix and match from assorted sell units to achieve consistent variation. Using a rubber grout float gently press the tile into adhesive to ensure complete contact.
Natural Stone should be sealed prior to grouting. A premium penetrating sealer is recommended for a natural look. Please refer to sealer manufacturer’s recommendations for application instructions.
Recommended Thin-Set: MAPEI Adesilex-P10 Premium Glass Tile Mortar mixed with MAPEI Keraply Latex Mortar Additive
Suggested Grout: MAPEI Ultracolor Plus FA, MAPEI FlexColor CQ or BOSTIK Trucolor Rapidcure
Cleaning: Clean all excess grout immediately with a damp sponge. After 12 hours polish off any remaining haze with a dry cloth or towel. For tough stains, we require the use of PH Neutral cleaner to clean the tile and grout, such as Grout & Tile neutral cleaner.
MAINTENANCE & CARE
Required to use a soft bristle brush to scrub the tile surfaces and grout. Take care to only use a soft bristle brush, to avoid the chance of scratching or damaging the grout. Then, simply wipe the surface, rinse well with clean water, and dry with a soft clean towel.
Required to use PH Neutral Cleaner to clean the tile and grout, such as Grout & Tile Neutral Cleaner
We strongly recommend customers to use a licensed tile contractor to do the tile installation and always use TCNA tile installation handbook as the installation guidance
Colors may vary from picture, Product may have chips, pitting and other characteristics, Pictures are only an indication of color, texture and finish
- 10.1 square feet, 10 pieces per case. Case weight is 20 lbs.
- Grade 1, first-quality porcelain tile for floor and wall use
- 11.88 in. width x 11.88 in. length x 0.26 in. thick mesh-mounted mosaic
- Glazed, smooth finish with a high sheen and moderate variation in tone
- PEI Rating II is suitable for all interior walls and light foot traffic such as powder rooms
- Impervious tiles have a water absorption of less than 0.5% for indoor and outdoor use and are frost resistant
- This tile is not ADA approved for slip resistance with a DCOF value less than 0.42.
- Completely frost resistant for indoor or outdoor applications; use a latex-modified thinset for acceptable bond strength
- WARNING: Silica dust is harmful if inhaled. Exposure to silica dust from cutting, grinding, or polishing can cause acute lung injury, silicosis or cancer. Wear a respirator when cutting, grinding, or polishing. Use wet cutting methods and do not dry cut. Children should not be present during cutting, grinding or polishing.
- Country of Origin: Indonesia
- Sheet size: 11 3/4" x 11 3/4"
- Tile Size: Random
- Tile thickness: 1/4" nominal
- Grout Joints: 1/8"
- Coverage Per Sheet: 0.96 SQF
- Sheet Mount: Mesh Backed
- Single Listing
- Total SQ FT in 1 quantity: 0.96 SQF
Areas of application and technical data:
- Floors: Light Residential
- Showers: Walls Only
- Pools: No
- Direct Sunlight: No
- Heat Resistant: Yes
- Frost Resistant: No
Pool Rated for use in Swimming Pools
Price per Sheet
Water Jet Mosaic Sapphire glass in water wave shape.
- Material: Glass
- Piece Size: 11 1/2" x 12 1/2"
- Sq Ft Per Piece: 1
- Colors: Sapphire
- Finish: Glossy
- Brighten up your pool or shower with this series
- Pool rated and acceptable for use on shower walls.
- The polyurethane cord backing makes installation easy.
- For use in Shower Walls, Shower Floors, Pools, Pool Liners, Interior Dry Walls, Interior Floors, Exterior Walls
- Installation Guide
Recommended Substrates:
- Properly cured mortar beds-ANSI A108.1B (cured a minimum of 7 days).
- Cementitious backer units (CBU)-ANSI A118.9.
- Concrete slabs cured for 28 days minimum.
- Gypsum board (dry areas only)-ASTM C1396 or ASTM C1396M-04.
- Note: An ANSI A108A-2.1.8 membrane is required behind all CBU installations in wet areas.
Setting Materials & Methods:
Setting material requirements will vary dependent upon the type of mosaic product being installed and the nature of the substrate.- Advice on the appropriate setting materials should be sought from your tile and stone dealer at the time of purchase.
- Only use setting materials that meet or exceed TCNA guidelines
- Only use an accredited licensed contractor experienced in the art of installing mosaic products.
- Setting methods must conform to the TCNA guidelines.
Note: Grout Selection:
The use of sanded and some premixed urethane micro glass bead enhanced grouts may cause damage to scratch sensitive surfaces. Always check with your Stone and Tile Dealer, Setting Contractor or Grout Manufacturer before selecting the grout type. Maniscalco is not responsible for any damage to the tile surface due to incorrect grout selection or incorrect grouting procedures.Measuring: Measure coverage area, make sure to purchase at least 10% extra material than is required. This will account for any breakage or mis-cuts during installation, and ensure you have extra material should you have to replace any tile elements in the future.
Cutting: Plan the placement of the tiles on your wall prior to installation. If you need to cut a mosaic sheet, cut from the back using a utility knife between tiles along the grout joints. Should you need to cut across tiles in a fashion that is not possible with a utility knife, use a wet saw with a diamond blade to cut through the tile.
Drilling: Using a drill bit designed for glass is recommended. When drilling the hole, keep the bit and hole lubricated to prevent chipping. Start by drilling from both ends of the tile, starting with the back and drilling half the depth of the tile. Then, turn the tile over and complete the hole is recommended. This will prevent the glass from chipping as the drill bit exits the tile.
Applying Setting Materials:
Apply setting material using the notched side of a V-notched trowel. Using the flat side of the trowels, smooth out all ridges to achieve a consistent, even 1/8” (3mm) coverage.Apply glass mosaic sheets, mesh -side down, firmly into freshly laid setting material. Mix and match from assorted sell units to achieve consistent variation. Using a rubber grout float gently press the tile into adhesive to ensure complete contact.
Natural Stone should be sealed prior to grouting. A premium penetrating sealer is recommended for a natural look. Please refer to sealer manufacturer’s recommendations for application instructions.
Recommended Thin-Set: MAPEI Adesilex-P10 Premium Glass Tile Mortar mixed with MAPEI Keraply Latex Mortar Additive
Suggested Grout: MAPEI Ultracolor Plus FA, MAPEI FlexColor CQ or BOSTIK Trucolor Rapidcure
Cleaning: Clean all excess grout immediately with a damp sponge. After 12 hours polish off any remaining haze with a dry cloth or towel. For tough stains, we require the use of PH Neutral cleaner to clean the tile and grout, such as Grout & Tile neutral cleaner.
MAINTENANCE & CARE
Required to use a soft bristle brush to scrub the tile surfaces and grout. Take care to only use a soft bristle brush, to avoid the chance of scratching or damaging the grout. Then, simply wipe the surface, rinse well with clean water, and dry with a soft clean towel.
Required to use PH Neutral Cleaner to clean the tile and grout, such as Grout & Tile Neutral Cleaner
We strongly recommend customers to use a licensed tile contractor to do the tile installation and always use TCNA tile installation handbook as the installation guidance
Colors may vary from picture, Product may have chips, pitting and other characteristics, Pictures are only an indication of color, texture and finish
Features :
- Set: comes in a box of 6 premium quality blue wall tiles, suitable for smooth and clean surfaces
- Premium Quality: wall peel and stick backsplash tiles are made of high-quality, durable eco-friendly PVC plastic, water-resistant and mold resistant which never turn yellow with time
- Versatile: use the peel and stick backsplash wallpaper for kitchen sink walls, bathroom backsplash, bedroom walls, laundry room, staircase, or on any other flat surfaces that are non-porous surfaces
- Easy DIY: simply peel off the backing and stick the self-adhesive backsplash tiles onto the desired spot without extra glue, no grout, no mess and no special tools or experience required
- Feature: easier to work with than big rolls or larger tiles as the size allows for a good stitching installation, can be bent to corner or cut by a sharp utility knife to fit perfectly
- Perfect Size: Each backsplash tile measures 10"L x 10"H in dimensions (approx. covers 4.17 sq. ft. per carton)
Specifications :
- Product Weight : 1.3 lbs
This porcelain mosaic tile from The Mosaic Factory is sophisticated, stylish, and suitable for any wall application, including but not limited to kitchen backsplashes, bathrooms, fireplaces, and pools. Sheets of tile are backed on mesh for easy installation. Glossy tiles can also be installed on bathroom floors (not shower floors) and other low traffic residential area's. Matte tiles can also be used on residential shower floors. Slip resistant tiles (The Mosaic Factory London series) can also be used in commercial high traffic areas like entrances, restrooms, and kitchen floors. The tiles can also be peeled off the mesh and installed individually, mixed with other colors.
Product Specifications
- Color: Jeans Blue
- Material: Porcelain
- Surface: Glossy
- Individual tile size (WxH): 5.7"x 0.8"
- Sheet size (WxH): 11.7"x 11.8" (0.95 sq. ft.)
- Thickness: 8 mm
- Grout joint: 3.5 mm
- Sheet backing: Mesh - ready for installation
- Impervious to liquids and vapors
- Resistant to fading, staining, and discoloration
- Shade variation: V1 - Uniform Appearance
- PEI rating: PEI 2 - Light Traffic
- Sample
- It is highly recommended to order a sample. Order multiple samples of the same product if it is a product with high shade variation. Sample is a cut piece of a sheet for color and texture reference. Samples are non returnable and non refundable.
- When measuring your project and ordering the product quantity make sure you order at least 10% extra for cuts, trimming, damaged pieces, and future repairs The installation is similar to the installation of wall tiles.
- Shipping and order quantity
- Due to the delicate nature of this tile, this item is only available for shipment on a pallet with a freight carrier.
- Therefore this item can only be ordered per increments of 60 sheets (6 boxes).
V1 - Uniform Appearance - Differences among pieces from the same production run are minimal V2 - Slight Variation - Clearly distinguishable differences in texture and/or pattern within similar colors V3 - Moderate Variation - While the colors present on a single piece of tile will be indicative of the colors to be expected on the other tiles, the amount of colors on each piece may vary significantly. For example 'that little bit of color' on one piece of tile may be the primary color on the next pieces. V4 - Substantial Variation - Random color differences from tile to tile, so that one tile may have totally different colors from that of other tiles. Thus the final installation will be unique.
PEI Rating
PEI is a measurement of the “abrasion resistance” of a tile, meaning how much “rubbing” does it take to physically impact the look of the tile. The test is scored on a scale and each value represents a durability to withstand increasingly more demanding traffic. PEI 1, Very Light Traffic - These tiles can be used on all indoor wall applications, for countertops such as bathrooms, and very light traffic residential bathroom floors. These tiles are not recommended for any area that will have any constant or heavy floor traffic. We do not recommend these to be used on floors at all. PEI 2, Light Traffic - These tiles can be used on all indoor wall applications, interior countertops applications and light traffic residential bathroom floors. These tiles should not be used in areas such as kitchens, entry ways, stairs or areas with heavy traffic. We recommend these only to be used on floors were you would normally walk barefoot / without shoes.
- 11.2 square feet, 10 pieces per case. Case weight is 19 lbs.
- Grade 1, first-quality porcelain tile for floor and wall use
- 11.88 in. width x 13.25 in. length x 0.19 in. thick mesh-mounted mosaic
- Glazed, smooth finish with a high sheen and slight variation in tone
- PEI Rating II is suitable for all interior walls and light foot traffic such as powder rooms
- Impervious tiles have a water absorption of less than 0.5% for indoor and outdoor use and are frost resistant
- This tile is not ADA approved for slip resistance with a DCOF value less than 0.42.
- Completely frost resistant for indoor or outdoor applications; use a latex-modified thinset for acceptable bond strength
- WARNING: Silica dust is harmful if inhaled. Exposure to silica dust from cutting, grinding, or polishing can cause acute lung injury, silicosis or cancer. Wear a respirator when cutting, grinding, or polishing. Use wet cutting methods and do not dry cut. Children should not be present during cutting, grinding or polishing.
- Country of Origin: Indonesia
Swimming Pool and Wet area Tiles
Color Stained glass tile mosaic
** Price is per Sheet (0.96 sq ft) ***
- Material: Glass
- Sheet Size: 11.75" x 11.75"
- Sq Ft Per Piece: 1.00
- Approximate Piece Size: 1" x 1"
- Thickness: 1/4"
- Colors: Blue Green
- Finish: Glossy
- Brighten up your pool or shower with this series of Handmade Porcelain mosaics.
- Pool rated and acceptable for use on shower walls.
- Use for Interior Dry Walls, Interior Floors, Shower Walls, Shower Floors, Pools, Pool Liners
- Installation Guide
Installation Instructions
Recommended Substrates:
- Properly cured mortar beds-ANSI A108.1B (cured a minimum of 7 days).
- Cementitious backer units (CBU)-ANSI A118.9.
- Concrete slabs cured for 28 days minimum.
- Gypsum board (dry areas only)-ASTM C1396 or ASTM C1396M-04.
- Note: An ANSI A108A-2.1.8 membrane is required behind all CBU installations in wet areas.
Setting Materials & Methods:
Setting material requirements will vary dependent upon the type of mosaic product being installed and the nature of the substrate.- Advice on the appropriate setting materials should be sought from your tile and stone dealer at the time of purchase.
- Only use setting materials that meet or exceed TCNA guidelines
- Only use an accredited licensed contractor experienced in the art of installing mosaic products.
- Setting methods must conform to the TCNA guidelines.
Note: Grout Selection:
The use of sanded and some premixed urethane micro glass bead enhanced grouts may cause damage to scratch sensitive surfaces. Always check with your Stone and Tile Dealer, Setting Contractor or Grout Manufacturer before selecting the grout type. Maniscalco is not responsible for any damage to the tile surface due to incorrect grout selection or incorrect grouting procedures.Colors may vary from picture, Product may have chips, pitting and other characteristics, Pictures are only an indication of color, texture and finish
Swimming Pool and Wet area Tiles
*** Price per Sheet (0.96 sq ft) ***
- Material: Handmade Porcelain
- Sheet Size: 11.75" x 11.75"
- Sq Ft Per Piece: 0.96
- Approximate Piece Size: 2" x 1"
- Thickness: 1/4"
- Colors: Royal Blue
- Finish: Glossy
- Brighten up your pool or shower with this series of Handmade Porcelain mosaics.
- Pool rated and acceptable for use on shower walls.
- Use for Pools, Pool Liners, Interior Dry, Shower Walls, Shower Floors, Walls, Interior Floors
- Installation Guide
Installation Instructions
Recommended Substrates:
- Properly cured mortar beds-ANSI A108.1B (cured a minimum of 7 days).
- Cementitious backer units (CBU)-ANSI A118.9.
- Concrete slabs cured for 28 days minimum.
- Gypsum board (dry areas only)-ASTM C1396 or ASTM C1396M-04.
- Note: An ANSI A108A-2.1.8 membrane is required behind all CBU installations in wet areas.
Setting Materials & Methods:
Setting material requirements will vary dependent upon the type of mosaic product being installed and the nature of the substrate.- Advice on the appropriate setting materials should be sought from your tile and stone dealer at the time of purchase.
- Only use setting materials that meet or exceed TCNA guidelines
- Only use an accredited licensed contractor experienced in the art of installing mosaic products.
- Setting methods must conform to the TCNA guidelines.
Note: Grout Selection:
The use of sanded and some premixed urethane micro glass bead enhanced grouts may cause damage to scratch sensitive surfaces. Always check with your Stone and Tile Dealer, Setting Contractor or Grout Manufacturer before selecting the grout type. Maniscalco is not responsible for any damage to the tile surface due to incorrect grout selection or incorrect grouting procedures.Colors may vary from picture, Product may have chips, pitting and other characteristics, Pictures are only an indication of color, texture and finish
- Size: 9.72 x 11.3 inch;
- Thickness: 5/16 inch;
- Finish: Polished (Glossy);
- Tile Size: 12 1/4" x 10 1/8"
- Tile Thickness: 1/4" nominal
- Grout Joint: 1/16"
- Coverage Per Sheet: 0.86 SQF
- Single Listing
- Total SQ FT in 1 quantity: 0.86 SQF
Areas of application and technical data:
- Floors: Light Residential
- Showers: Yes
- Pools: No
- Direct Sunlight: Yes
- Heat Resistant: Yes
- Frost Resistant: Yes
Pool Rated for use in Swimming Pools
Price per Sheet
Water jet The Rift glass piece precisely cut to create perfect wave-like pattern.
- Material: Glass
- Piece Size: 11 1/2" x 12 1/2"
- Sq Ft Per Piece: 1
- Thickness: 3/8"
- Colors: The Rift
- Finish: Glossy
- Brighten up your pool or shower with this series
- Pool rated and acceptable for use on shower walls.
- The polyurethane cord backing makes installation easy.
- For use in Shower Walls, Shower Floors, Pools, Pool Liners, Interior Dry Walls, Interior Floors, Exterior Walls
- Installation Guide
Recommended Substrates:
- Properly cured mortar beds-ANSI A108.1B (cured a minimum of 7 days).
- Cementitious backer units (CBU)-ANSI A118.9.
- Concrete slabs cured for 28 days minimum.
- Gypsum board (dry areas only)-ASTM C1396 or ASTM C1396M-04.
- Note: An ANSI A108A-2.1.8 membrane is required behind all CBU installations in wet areas.
Setting Materials & Methods:
Setting material requirements will vary dependent upon the type of mosaic product being installed and the nature of the substrate.- Advice on the appropriate setting materials should be sought from your tile and stone dealer at the time of purchase.
- Only use setting materials that meet or exceed TCNA guidelines
- Only use an accredited licensed contractor experienced in the art of installing mosaic products.
- Setting methods must conform to the TCNA guidelines.
Note: Grout Selection:
The use of sanded and some premixed urethane micro glass bead enhanced grouts may cause damage to scratch sensitive surfaces. Always check with your Stone and Tile Dealer, Setting Contractor or Grout Manufacturer before selecting the grout type. Maniscalco is not responsible for any damage to the tile surface due to incorrect grout selection or incorrect grouting procedures.Measuring: Measure coverage area, make sure to purchase at least 10% extra material than is required. This will account for any breakage or mis-cuts during installation, and ensure you have extra material should you have to replace any tile elements in the future.
Cutting: Plan the placement of the tiles on your wall prior to installation. If you need to cut a mosaic sheet, cut from the back using a utility knife between tiles along the grout joints. Should you need to cut across tiles in a fashion that is not possible with a utility knife, use a wet saw with a diamond blade to cut through the tile.
Drilling: Using a drill bit designed for glass is recommended. When drilling the hole, keep the bit and hole lubricated to prevent chipping. Start by drilling from both ends of the tile, starting with the back and drilling half the depth of the tile. Then, turn the tile over and complete the hole is recommended. This will prevent the glass from chipping as the drill bit exits the tile.
Applying Setting Materials:
Apply setting material using the notched side of a V-notched trowel. Using the flat side of the trowels, smooth out all ridges to achieve a consistent, even 1/8” (3mm) coverage.Apply glass mosaic sheets, mesh -side down, firmly into freshly laid setting material. Mix and match from assorted sell units to achieve consistent variation. Using a rubber grout float gently press the tile into adhesive to ensure complete contact.
Natural Stone should be sealed prior to grouting. A premium penetrating sealer is recommended for a natural look. Please refer to sealer manufacturer’s recommendations for application instructions.
Recommended Thin-Set: MAPEI Adesilex-P10 Premium Glass Tile Mortar mixed with MAPEI Keraply Latex Mortar Additive
Suggested Grout: MAPEI Ultracolor Plus FA, MAPEI FlexColor CQ or BOSTIK Trucolor Rapidcure
Cleaning: Clean all excess grout immediately with a damp sponge. After 12 hours polish off any remaining haze with a dry cloth or towel. For tough stains, we require the use of PH Neutral cleaner to clean the tile and grout, such as Grout & Tile neutral cleaner.
MAINTENANCE & CARE
Required to use a soft bristle brush to scrub the tile surfaces and grout. Take care to only use a soft bristle brush, to avoid the chance of scratching or damaging the grout. Then, simply wipe the surface, rinse well with clean water, and dry with a soft clean towel.
Required to use PH Neutral Cleaner to clean the tile and grout, such as Grout & Tile Neutral Cleaner
We strongly recommend customers to use a licensed tile contractor to do the tile installation and always use TCNA tile installation handbook as the installation guidance
Colors may vary from picture, Product may have chips, pitting and other characteristics, Pictures are only an indication of color, texture and finish
Swimming Pool and Wet area Tiles
Price per Sheet (1.05 sq ft)
- Material: Glass mosaic made of 98% recycled glass tile from Spain
- Sheet Size: 12 1/4" x 12 1/2"
- Sq Ft Per Piece: 1.57
- Piece Size: 2" x 2"
- Thickness: 1/8"
- Colors: Blue Fountain
- Finish: Glossy
- Backing: Polyurethane Cord
- Brighten up your pool or shower with this series of 100% recycled glass mosaics.
- Pool rated and acceptable for use on shower walls.
- The polyurethane cord backing makes installation easy.
- Use for Interior Dry Walls, Interior Floors, Shower Walls, Shower Floors, Pools, Pool Liners, Exterior Walls
- Installation Guide
Installation Instructions
Recommended Substrates:
- Properly cured mortar beds-ANSI A108.1B (cured a minimum of 7 days).
- Cementitious backer units (CBU)-ANSI A118.9.
- Concrete slabs cured for 28 days minimum.
- Gypsum board (dry areas only)-ASTM C1396 or ASTM C1396M-04.
- Note: An ANSI A108A-2.1.8 membrane is required behind all CBU installations in wet areas.
Setting Materials & Methods:
Setting material requirements will vary dependent upon the type of mosaic product being installed and the nature of the substrate.- Advice on the appropriate setting materials should be sought from your tile and stone dealer at the time of purchase.
- Only use setting materials that meet or exceed TCNA guidelines
- Only use an accredited licensed contractor experienced in the art of installing mosaic products.
- Setting methods must conform to the TCNA guidelines.
- Do not cover/protect the Victoria Metals with adhesive tape of any kind.
Note: Grout Selection:
The use of sanded and some premixed urethane micro glass bead enhanced grouts may cause damage to scratch sensitive surfaces. Always check with your Stone and Tile Dealer, Setting Contractor or Grout Manufacturer before selecting the grout type. Maniscalco is not responsible for any damage to the tile surface due to incorrect grout selection or incorrect grouting procedures.Sealing Guide:
- Sealing prior to grouting is recommended for all stone mosaics.
- Glass (see note below), Stainless Steel, Antique Copper and Aluminum mosaics do not require sealing.
- Note: Pre sealing prior to setting is necessary when installing Barossa Valley Crystal Glass.
- Note: Only use water based sealers with Sydney Harbor Metals.
- Note: When sealing Botany Bay pebbles expect some darkening of the color. Test sealer on a sample area first.
- Colors may vary from picture, Product may have chips, pitting and other characteristics, Pictures are only an indication of color, texture and finish
- 9.8 square feet, 10 pieces per case. Case weight is 24.3 lbs.
- Grade 1, first-quality porcelain tile for floor and wall use
- 11.75 in. width x 11.75 in. length x 0.28 in. thick mesh-mounted mosaic
- Glazed, smooth finish with a high sheen and slight variation in tone
- PEI Rating II is suitable for all interior walls and light foot traffic such as powder rooms
- Impervious tiles have a water absorption of less than 0.5% for indoor and outdoor use and are frost resistant
- This tile has a COF wet rating less than or equal to 0.50 and is considered to have a marginally low skid resistance. This tile is not ADA approved for slip resistance.
- Completely frost resistant for indoor or outdoor applications; use a latex-modified thinset for acceptable bond strength
- WARNING: Silica dust is harmful if inhaled. Exposure to silica dust from cutting, grinding, or polishing can cause acute lung injury, silicosis or cancer. Wear a respirator when cutting, grinding, or polishing. Use wet cutting methods and do not dry cut. Children should not be present during cutting, grinding or polishing.
- Country of Origin: Thailand
- MOSAICS MARBLE ONYX HEXAGON 3X3 - GREEN
- 3x3 Hexagon mosaic made of Green Onyx.
- Material: Onyx
- Piece Size: 10.25" x 11.75"
- Individual Size: 3" x 3"
- Sq Ft Per Piece: 0.84
- Thickness: 3/8"
- Colors: Mixed Green and White
- Finish: Glossy
- Use for Residential / Commercial, Interior Dry Walls, Interior Floors, Shower Walls, Shower Floors, Exterior Walls
- Installation Guide
- Size: 10.43 x 10.43 inch;
- Thickness: 5/16 inch;
- Finish: Polished (Glossy);
- 8.6 square feet, 10 pieces per case. Case weight is 17.81 lbs.
- Grade 1, first-quality porcelain tile for floor and wall use
- 10.25 in. width x 11.88 in. length x 0.22 in. thick mesh-mounted mosaic
- Glazed, smooth finish with a high sheen and uniform appearance in tone
- PEI Rating IV has high resistance to abrasion and is suitable for heavy-duty residential and commercial kitchens, hotels, exhibition and sales rooms with some dirt conditions
- Impervious tiles have a water absorption of less than 0.5% for indoor and outdoor use and are frost resistant
- This tile has a COF wet rating less than or equal to 0.50 and is considered to have a marginally low skid resistance. This tile is not ADA approved for slip resistance.
- Completely frost resistant for indoor or outdoor applications; use a latex-modified thinset for acceptable bond strength
- WARNING: Silica dust is harmful if inhaled. Exposure to silica dust from cutting, grinding, or polishing can cause acute lung injury, silicosis or cancer. Wear a respirator when cutting, grinding, or polishing. Use wet cutting methods and do not dry cut. Children should not be present during cutting, grinding or polishing.
- Country of Origin: Thailand
- 10.6 square feet, 10 pieces per case. Case weight is 20 lbs.
- Grade 1, first-quality porcelain tile for floor and wall use
- 11.38 in. width x 13.13 in. length x 0.25 in. thick mesh-mounted mosaic
- Glazed, smooth finish with a high sheen and uniform appearance in tone
- PEI Rating IV has high resistance to abrasion and is suitable for heavy-duty residential and commercial kitchens, hotels, exhibition and sales rooms with some dirt conditions
- Impervious tiles have a water absorption of less than 0.5% for indoor and outdoor use and are frost resistant
- This tile has a COF wet rating less than or equal to 0.50 and is considered to have a marginally low skid resistance. This tile is not ADA approved for slip resistance.
- Completely frost resistant for indoor or outdoor applications; use a latex-modified thinset for acceptable bond strength
- WARNING: Silica dust is harmful if inhaled. Exposure to silica dust from cutting, grinding, or polishing can cause acute lung injury, silicosis or cancer. Wear a respirator when cutting, grinding, or polishing. Use wet cutting methods and do not dry cut. Children should not be present during cutting, grinding or polishing.
- Country of Origin: Indonesia
- 10.0 square feet, 10 pieces per case. Case weight is 25.33 lbs.
- Grade 1, first-quality porcelain tile for floor and wall use
- 11.13 in. width x 12.63 in. length x 0.27 in. thick mesh-mounted mosaic
- Glazed, smooth finish with a high sheen and uniform appearance in tone
- PEI Rating II is suitable for all interior walls and light foot traffic such as powder rooms
- Impervious tiles have a water absorption of less than 0.5% for indoor and outdoor use and are frost resistant
- This tile has a COF wet rating less than or equal to 0.50 and is considered to have a marginally low skid resistance. This tile is not ADA approved for slip resistance.
- Completely frost resistant for indoor or outdoor applications; use a latex-modified thinset for acceptable bond strength
- WARNING: Silica dust is harmful if inhaled. Exposure to silica dust from cutting, grinding, or polishing can cause acute lung injury, silicosis or cancer. Wear a respirator when cutting, grinding, or polishing. Use wet cutting methods and do not dry cut. Children should not be present during cutting, grinding or polishing.
- Country of Origin: Thailand
Pool Rated for use in Swimming Pools
Price per Sheet
Water Blue-Water jet mosaic, white, light blue and dark blue glass in water wave interlocking pattern art mosaic
- Material: Glass
- Piece Size: 11 1/2" x 12 1/2"
- Sq Ft Per Piece: 1
- Thickness: 3/8"
- Colors: Ocean Blue
- Finish: Glossy
- Brighten up your pool or shower with this series
- Pool rated and acceptable for use on shower walls.
- The polyurethane cord backing makes installation easy.
- For use in Shower Walls, Shower Floors, Pools, Pool Liners, Interior Dry Walls, Interior Floors, Exterior Walls
- Installation Guide
Recommended Substrates:
- Properly cured mortar beds-ANSI A108.1B (cured a minimum of 7 days).
- Cementitious backer units (CBU)-ANSI A118.9.
- Concrete slabs cured for 28 days minimum.
- Gypsum board (dry areas only)-ASTM C1396 or ASTM C1396M-04.
- Note: An ANSI A108A-2.1.8 membrane is required behind all CBU installations in wet areas.
Setting Materials & Methods:
Setting material requirements will vary dependent upon the type of mosaic product being installed and the nature of the substrate.- Advice on the appropriate setting materials should be sought from your tile and stone dealer at the time of purchase.
- Only use setting materials that meet or exceed TCNA guidelines
- Only use an accredited licensed contractor experienced in the art of installing mosaic products.
- Setting methods must conform to the TCNA guidelines.
Note: Grout Selection:
The use of sanded and some premixed urethane micro glass bead enhanced grouts may cause damage to scratch sensitive surfaces. Always check with your Stone and Tile Dealer, Setting Contractor or Grout Manufacturer before selecting the grout type. Maniscalco is not responsible for any damage to the tile surface due to incorrect grout selection or incorrect grouting procedures.Measuring: Measure coverage area, make sure to purchase at least 10% extra material than is required. This will account for any breakage or mis-cuts during installation, and ensure you have extra material should you have to replace any tile elements in the future.
Cutting: Plan the placement of the tiles on your wall prior to installation. If you need to cut a mosaic sheet, cut from the back using a utility knife between tiles along the grout joints. Should you need to cut across tiles in a fashion that is not possible with a utility knife, use a wet saw with a diamond blade to cut through the tile.
Drilling: Using a drill bit designed for glass is recommended. When drilling the hole, keep the bit and hole lubricated to prevent chipping. Start by drilling from both ends of the tile, starting with the back and drilling half the depth of the tile. Then, turn the tile over and complete the hole is recommended. This will prevent the glass from chipping as the drill bit exits the tile.
Applying Setting Materials:
Apply setting material using the notched side of a V-notched trowel. Using the flat side of the trowels, smooth out all ridges to achieve a consistent, even 1/8” (3mm) coverage.Apply glass mosaic sheets, mesh -side down, firmly into freshly laid setting material. Mix and match from assorted sell units to achieve consistent variation. Using a rubber grout float gently press the tile into adhesive to ensure complete contact.
Natural Stone should be sealed prior to grouting. A premium penetrating sealer is recommended for a natural look. Please refer to sealer manufacturer’s recommendations for application instructions.
Recommended Thin-Set: MAPEI Adesilex-P10 Premium Glass Tile Mortar mixed with MAPEI Keraply Latex Mortar Additive
Suggested Grout: MAPEI Ultracolor Plus FA, MAPEI FlexColor CQ or BOSTIK Trucolor Rapidcure
Cleaning: Clean all excess grout immediately with a damp sponge. After 12 hours polish off any remaining haze with a dry cloth or towel. For tough stains, we require the use of PH Neutral cleaner to clean the tile and grout, such as Grout & Tile neutral cleaner.
MAINTENANCE & CARE
Required to use a soft bristle brush to scrub the tile surfaces and grout. Take care to only use a soft bristle brush, to avoid the chance of scratching or damaging the grout. Then, simply wipe the surface, rinse well with clean water, and dry with a soft clean towel.
Required to use PH Neutral Cleaner to clean the tile and grout, such as Grout & Tile Neutral Cleaner
We strongly recommend customers to use a licensed tile contractor to do the tile installation and always use TCNA tile installation handbook as the installation guidance
Colors may vary from picture, Product may have chips, pitting and other characteristics, Pictures are only an indication of color, texture and finish
- 10.6 square feet, 10 pieces per case. Case weight is 23.2 lbs.
- Grade 1, first-quality porcelain tile for floor and wall use
- 12 in. width x 12.5 in. length x 0.19 in. thick mesh-mounted mosaic
- Glazed, smooth finish with a high sheen and moderate variation in tone
- PEI Rating II is suitable for all interior walls and light foot traffic such as powder rooms
- Impervious tiles have a water absorption of less than 0.5% for indoor and outdoor use and are frost resistant
- This tile has a COF wet rating less than or equal to 0.50 and is considered to have a marginally low skid resistance. This tile is not ADA approved for slip resistance.
- Completely frost resistant for indoor or outdoor applications; use a latex-modified thinset for acceptable bond strength
- WARNING: Silica dust is harmful if inhaled. Exposure to silica dust from cutting, grinding, or polishing can cause acute lung injury, silicosis or cancer. Wear a respirator when cutting, grinding, or polishing. Use wet cutting methods and do not dry cut. Children should not be present during cutting, grinding or polishing.
- Country of Origin: Indonesia
Swimming Pool and Wet area Tiles
Color Stained glass tile mosaic
*** Price per Sheet (0.96 sq ft) ***
- Material: Glass
- Sheet Size: 11.75" x 11.75"
- Sq Ft Per Piece: 1.00
- Approximate Piece Size: 1" x 1"
- Thickness: 1/4"
- Colors: Light Blue
- Finish: Glossy
- Backing: Face mount
- Brighten up your pool or shower with this series of Handmade Porcelain mosaics.
- Pool rated and acceptable for use on shower walls.
- Use for Interior Dry Walls, Interior Floors, Shower Walls, Shower Floors, Pools, Pool Liners
- Installation Guide
Installation Instructions
Recommended Substrates:
- Properly cured mortar beds-ANSI A108.1B (cured a minimum of 7 days).
- Cementitious backer units (CBU)-ANSI A118.9.
- Concrete slabs cured for 28 days minimum.
- Gypsum board (dry areas only)-ASTM C1396 or ASTM C1396M-04.
- Note: An ANSI A108A-2.1.8 membrane is required behind all CBU installations in wet areas.
Setting Materials & Methods:
Setting material requirements will vary dependent upon the type of mosaic product being installed and the nature of the substrate.- Advice on the appropriate setting materials should be sought from your tile and stone dealer at the time of purchase.
- Only use setting materials that meet or exceed TCNA guidelines
- Only use an accredited licensed contractor experienced in the art of installing mosaic products.
- Setting methods must conform to the TCNA guidelines.
Note: Grout Selection:
The use of sanded and some premixed urethane micro glass bead enhanced grouts may cause damage to scratch sensitive surfaces. Always check with your Stone and Tile Dealer, Setting Contractor or Grout Manufacturer before selecting the grout type. Maniscalco is not responsible for any damage to the tile surface due to incorrect grout selection or incorrect grouting procedures.Colors may vary from picture, Product may have chips, pitting and other characteristics, Pictures are only an indication of color, texture and finish