Item 1 of 2
Item 1 of 2
- Product Description
- Product Specifications
- Shipping and Returns
*Please Note**
- Please see secondary image for color swatch
- New: Hardwood Tones
- Ipe: Rich, Lustrous Deep Brown Enhances the Natural Colors of Wood Like Ipe, Pau'd Arco & Ironwood
- Tigerwood: A Perfect tone, Deep Rich Red with Black Undertones, for Tigerwood and Other African Walnut Species
See the color chart for more details.
- Wood stain especially formulated to penetrate dense hardwoods
- Added ultraviolet protection
- Transparent natural tone allows the beauty of wood to be seen
- Used on some of the largest theme park boardwalks in the world
- Advanced mildew protection
- Not a surface film that will crack, bubble, or peel
- Application
- Use ProTech Stripper to remove any non-Penofin stain. If wood is gray use Pro-Tech Brightener to restore the wood's original appearance.
- Shake well before using. Do not add thinning or blending agents.
- Brush on, use a stain pad, or spray on using a pump up sprayer equipped with plastic tip.
- To allow for maximum penetration wait 30 minutes, then use a nap-free shop cloth and wipe the entire surface, removing excess product.
- Surface will be dry to the touch in three hours, and ready for use in 12 hours.
- When using the one-coat formula, the application is now complete.
- Do not apply wet-on-wet.
- Product Performance Warranty
Color Test
It is best to test Penofin on your wood to determine the desired color. The shade can be affected by the type of wood, the manner applied, the length of time the oil is left on, and by the number of coats. If the desired color is attained with one coat of a pigmented formula, the wet-sand process may be done with Penofin Natural.
- Maintenance
- Follow the application methods listed on the previous page for a fresh and beautiful wood surface.
Coverage depends on application method, texture, and moisture content of wood. Coverage is less on rough surfaces, more on smooth surfaces. Average coverage is 175-300 sq. ft. per gallon.
- Cleanup
- Penofin is an oil-based product. Clean brushes and other application materials with mineral spirits or paint thinner.
According to the Columbia Encyclopedia, Sixth Edition. 2001, "Spontaneous combustion is a phenomenon in which a substance unexpectedly bursts into flame without apparent cause. In ordinary combustion, a substance is deliberately heated to its ignition point to make it burn. Many substances undergo a slow oxidation that, like the rapid oxidation of burning, releases heat. If the heat so released cannot escape the substance, the temperature of the substance rises until ignition takes place. Spontaneous combustion often occurs in piles of oily rags, green hay, leaves, or coal; it can constitute a serious fire hazard."
Hardwood Application
Use a brush or sprayer. Brushing gives best results. Brush thoroughly and back brush Penofin into the wood leaving no excess. Wipe entire surface after 20-30 minutes with a nap-free cloth. Do not allow film to develop on wood surface. Apply when there is no chance of rain during the process or during the twelve-hour drying time. If rain occurs spots may develop on wood surfaces. Do not apply in direct hot sun! A minimum air temperature of 45° is required during application and drying time.
Repeat this application within 3-6 months and again within 10-12 months. Over time the wood fibers will become fully protected and maintenance will become less frequent. Product should be applied more often to horizontal areas and also areas with high ultra-violet exposure or heavy traffic. Store all oily cloths in water in a metal bucket until properly disposed.
- Coverage
- 400 square feet per gallon.
- Maintenance
- Follow the application methods listed on the previous page for a fresh and beautiful wood
- Surface
- Trouble-Shooting A Sticky-Tacky Surface
- Avoid overapplication by following the instructions we just covered. In the event of an overapplication, use the following methods to resolve.
- To Remove Excess
- Allow Penofin to dry for seven days.
- Use Penofin Protech Cleaner and scrub the surface with a nylon or natural bristle brush. Do not use metal brushes.
- You may also use Penofin Wood Stripper for tough jobs.
- Allow the surface to dry for 48 hours before reapplying
Penofin Exotic Hardwood Formula, Penetrating Wood Stain, 1 Gallon, Ipe
By Penofin
37 Reviews
$73
Sold Out
Color:Ipe
*Please Note**
- Please see secondary image for color swatch
- New: Hardwood Tones
- Ipe: Rich, Lustrous Deep Brown Enhances the Natural Colors of Wood Like Ipe, Pau'd Arco & Ironwood
- Tigerwood: A Perfect tone, Deep Rich Red with Black Undertones, for Tigerwood and Other African Walnut Species
See the color chart for more details.
- Wood stain especially formulated to penetrate dense hardwoods
- Added ultraviolet protection
- Transparent natural tone allows the beauty of wood to be seen
- Used on some of the largest theme park boardwalks in the world
- Advanced mildew protection
- Not a surface film that will crack, bubble, or peel
- Application
- Use ProTech Stripper to remove any non-Penofin stain. If wood is gray use Pro-Tech Brightener to restore the wood's original appearance.
- Shake well before using. Do not add thinning or blending agents.
- Brush on, use a stain pad, or spray on using a pump up sprayer equipped with plastic tip.
- To allow for maximum penetration wait 30 minutes, then use a nap-free shop cloth and wipe the entire surface, removing excess product.
- Surface will be dry to the touch in three hours, and ready for use in 12 hours.
- When using the one-coat formula, the application is now complete.
- Do not apply wet-on-wet.
- Product Performance Warranty
Color Test
It is best to test Penofin on your wood to determine the desired color. The shade can be affected by the type of wood, the manner applied, the length of time the oil is left on, and by the number of coats. If the desired color is attained with one coat of a pigmented formula, the wet-sand process may be done with Penofin Natural.
- Maintenance
- Follow the application methods listed on the previous page for a fresh and beautiful wood surface.
Coverage depends on application method, texture, and moisture content of wood. Coverage is less on rough surfaces, more on smooth surfaces. Average coverage is 175-300 sq. ft. per gallon.
- Cleanup
- Penofin is an oil-based product. Clean brushes and other application materials with mineral spirits or paint thinner.
According to the Columbia Encyclopedia, Sixth Edition. 2001, "Spontaneous combustion is a phenomenon in which a substance unexpectedly bursts into flame without apparent cause. In ordinary combustion, a substance is deliberately heated to its ignition point to make it burn. Many substances undergo a slow oxidation that, like the rapid oxidation of burning, releases heat. If the heat so released cannot escape the substance, the temperature of the substance rises until ignition takes place. Spontaneous combustion often occurs in piles of oily rags, green hay, leaves, or coal; it can constitute a serious fire hazard."
Hardwood Application
Use a brush or sprayer. Brushing gives best results. Brush thoroughly and back brush Penofin into the wood leaving no excess. Wipe entire surface after 20-30 minutes with a nap-free cloth. Do not allow film to develop on wood surface. Apply when there is no chance of rain during the process or during the twelve-hour drying time. If rain occurs spots may develop on wood surfaces. Do not apply in direct hot sun! A minimum air temperature of 45° is required during application and drying time.
Repeat this application within 3-6 months and again within 10-12 months. Over time the wood fibers will become fully protected and maintenance will become less frequent. Product should be applied more often to horizontal areas and also areas with high ultra-violet exposure or heavy traffic. Store all oily cloths in water in a metal bucket until properly disposed.
- Coverage
- 400 square feet per gallon.
- Maintenance
- Follow the application methods listed on the previous page for a fresh and beautiful wood
- Surface
- Trouble-Shooting A Sticky-Tacky Surface
- Avoid overapplication by following the instructions we just covered. In the event of an overapplication, use the following methods to resolve.
- To Remove Excess
- Allow Penofin to dry for seven days.
- Use Penofin Protech Cleaner and scrub the surface with a nylon or natural bristle brush. Do not use metal brushes.
- You may also use Penofin Wood Stripper for tough jobs.
- Allow the surface to dry for 48 hours before reapplying
- Product ID
- 51674811
- Manufactured By
- Penofin
- Sold By
- Quality Construction Supply
- Size/Weight
- W 10" / D 10" / H 10" / 10 lb.
- Color
- Ipe
- Materials
- rosewood oil
- Category
- Stains And Varnishes
- Style
- Traditional
CA Residents: Prop 65 Warning
Product Options
- Color: Natural
- Color: Ipe
- Color: Tigerwood
Sold by Quality Construction Supply- Free shipping!
Ready to ship to the contiguous U.S. in 1-4 days
This product does not ship to Canada
Note: Free shipping is not available to AK, HI, PR or Canada. Some exclusions apply.
Houzz offers a 30-day standard return policy for most items. We also accept returns on damaged large or oversized items that ship via freight, as long as you report the damage within 5 days of delivery. View our full return policy.
- Product Description
- Product Specifications
- Shipping and Returns
*Please Note**
- Please see secondary image for color swatch
- New: Hardwood Tones
- Ipe: Rich, Lustrous Deep Brown Enhances the Natural Colors of Wood Like Ipe, Pau'd Arco & Ironwood
- Tigerwood: A Perfect tone, Deep Rich Red with Black Undertones, for Tigerwood and Other African Walnut Species
See the color chart for more details.
- Wood stain especially formulated to penetrate dense hardwoods
- Added ultraviolet protection
- Transparent natural tone allows the beauty of wood to be seen
- Used on some of the largest theme park boardwalks in the world
- Advanced mildew protection
- Not a surface film that will crack, bubble, or peel
- Application
- Use ProTech Stripper to remove any non-Penofin stain. If wood is gray use Pro-Tech Brightener to restore the wood's original appearance.
- Shake well before using. Do not add thinning or blending agents.
- Brush on, use a stain pad, or spray on using a pump up sprayer equipped with plastic tip.
- To allow for maximum penetration wait 30 minutes, then use a nap-free shop cloth and wipe the entire surface, removing excess product.
- Surface will be dry to the touch in three hours, and ready for use in 12 hours.
- When using the one-coat formula, the application is now complete.
- Do not apply wet-on-wet.
- Product Performance Warranty
Color Test
It is best to test Penofin on your wood to determine the desired color. The shade can be affected by the type of wood, the manner applied, the length of time the oil is left on, and by the number of coats. If the desired color is attained with one coat of a pigmented formula, the wet-sand process may be done with Penofin Natural.
- Maintenance
- Follow the application methods listed on the previous page for a fresh and beautiful wood surface.
Coverage depends on application method, texture, and moisture content of wood. Coverage is less on rough surfaces, more on smooth surfaces. Average coverage is 175-300 sq. ft. per gallon.
- Cleanup
- Penofin is an oil-based product. Clean brushes and other application materials with mineral spirits or paint thinner.
According to the Columbia Encyclopedia, Sixth Edition. 2001, "Spontaneous combustion is a phenomenon in which a substance unexpectedly bursts into flame without apparent cause. In ordinary combustion, a substance is deliberately heated to its ignition point to make it burn. Many substances undergo a slow oxidation that, like the rapid oxidation of burning, releases heat. If the heat so released cannot escape the substance, the temperature of the substance rises until ignition takes place. Spontaneous combustion often occurs in piles of oily rags, green hay, leaves, or coal; it can constitute a serious fire hazard."
Hardwood Application
Use a brush or sprayer. Brushing gives best results. Brush thoroughly and back brush Penofin into the wood leaving no excess. Wipe entire surface after 20-30 minutes with a nap-free cloth. Do not allow film to develop on wood surface. Apply when there is no chance of rain during the process or during the twelve-hour drying time. If rain occurs spots may develop on wood surfaces. Do not apply in direct hot sun! A minimum air temperature of 45° is required during application and drying time.
Repeat this application within 3-6 months and again within 10-12 months. Over time the wood fibers will become fully protected and maintenance will become less frequent. Product should be applied more often to horizontal areas and also areas with high ultra-violet exposure or heavy traffic. Store all oily cloths in water in a metal bucket until properly disposed.
- Coverage
- 400 square feet per gallon.
- Maintenance
- Follow the application methods listed on the previous page for a fresh and beautiful wood
- Surface
- Trouble-Shooting A Sticky-Tacky Surface
- Avoid overapplication by following the instructions we just covered. In the event of an overapplication, use the following methods to resolve.
- To Remove Excess
- Allow Penofin to dry for seven days.
- Use Penofin Protech Cleaner and scrub the surface with a nylon or natural bristle brush. Do not use metal brushes.
- You may also use Penofin Wood Stripper for tough jobs.
- Allow the surface to dry for 48 hours before reapplying
At Houzz we want you to shop for Penofin Penofin Exotic Hardwood Formula, Penetrating Wood Stain, 1 Gallon, Ipe with confidence. You can read real customer reviews for this or any other product and even ask questions and get answers from us or straight from the brand. When you buy Penofin Penofin Exotic Hardwood Formula, Penetrating Wood Stain, 1 Gallon, Ipe or any product product online from us, you become part of the Houzz family and can expect exceptional customer service every step of the way. If you have questions about Penofin or any other product for sale, our customer service team is eager to help.