FREE shipping on orders over $49!* Details
- All Products
- Bath
- Cabinet & Drawer Hardware
- Brand: Prime-Line Products
Avondale Decor, LLC and Prime-Line Products Traditional Cabinet and Drawer Hardware
Item 1 of 2
By- Pass Closet, 96" Track, Use with 2 and 3-Door Systems, 1-trackby Prime-Line Products
$47
This by-pass closet door track is constructed of galvanized steel. It features the same double J-track as those used in Prime-Line's 2-door kits, and it can also be used with 3-door by-pass systems. The track length is pre-cut to 95 in. to minimize the need for cutting, and it is commonly used with wooden door panels measuring from 3/4 in. thick to 1-3/8 in. thick. This track will safely hold doors that weigh up to 60 lbs. each, and it can be used to mount one panel on each track or one panel on one track and two panels on the second.
- Used to hang two and three door, by-passing sliding closet door panels
- Accepts 3/4 in., 7/8 in., 1-1/8 in. or 1-3/8 in. thick doors
- Galvanized steel construction
- Constructed of one solid piece of track
- Installation fasteners are included with this item
- For further dimensional information, please see the line drawing
Best Seller
19-3/4" White Painted Steel Bottom-Mount Self-Closing Drawer Slides, 1-pairby Prime-Line Products(4218)
SALE
$24$29
These drawer slide kits are constructed of steel tracks with plastic rollers and come in a white powder-coated finish. They feature a self-closing design that commences at the final 2-1/2 in. from the end of the 19-3/4 in. long tracks when closing. The maximum load capacity for this kit is 75 lbs., and it fits most bottom-mount drawer systems. This kit cannot be cut down to fit smaller drawer depths as it is designed with a positive stop at the ends of the fixed tracks, and because the rear rollers (11/16 in. diameter wheels) on the sliding tracks are fastened to the ends of the drawer-mounted track pieces. These bottom-mount drawer slides can be installed in drawer cabinets with face frames and without. If installing in drawer cabinet with face frame, Prime-Line part R 7240 (purchased separately) may be necessary if existing back plates are damaged. The clearance required between the drawer and the drawer opening for these types of slides is as follows: 1/2 in. on left and right sides, 1/4 in. at the bottom and 5/8 in. at the top. Installation instructions are included with each set, and they can also be found within the manufacturer�s website.
- These drawer slides can be installed in cabinetry constructed with and without face frames, that have a depth of 20 in.
- Durable steel-constructed drawer slides with plastic wheels designed for years of use
- Designed with self-closing feature that begins towards the end of the slide
- Easy to install slides fit most bottom-mount drawer systems
- Maximum load capacity is 75 lbs.
- Ideal for use in kitchen cabinets
- Installation fasteners and instructions are included
- For further dimensional information, please see the line drawing
1", Front Drawer Guide Rollersby Prime-Line Products(1018)
$18
These roller assemblies are constructed of steel brackets and plastic wheels, and they're manufactured in a left and right-hand roller assembly. The roller assemblies are used to replace worn or missing guide buttons, allowing the drawers to glide easily when opening and closing, while at the same time preventing wear on the cabinet�s face frame or drawer opening. These roller assemblies install into the inside lower left and right corners of the drawer face opening with necessary fasteners provided within each kit. This pair of roller assemblies have a max load rating of 20 lbs., and they are used by many to replace missing or malfunctioning drawer track hardware. For a complete kit with track, guide and back plate, see Prime-Line part R 7137.
- Used on the front of drawer opening to aid in a smoother operation
- Features a 1 in. outside diameter roller, 9/16 in. wide
- Used to help center your drawer
- Constructed of steel brackets and plastic wheels
- Includes 1 left hand and 1 right hand roller assembly
- Mounting hardware included
- A Phillips head screwdriver is required for installation
- For further dimensional information, please see the line drawing
Drawer Track Back Plate, 2Packby Prime-Line Products(3)
$18
This back plate is constructed from plastic and is used to hold your track to the back of your cabinet. It features a reversible design for right or left-handed tracks. Fits on most popular side mount rails.
- Reversible for right or left hand track
- Mounts in back of cabinet, supports track
- White in color
- Easy to install with a few simple tools
- Installation fasteners are included
- For further dimensional information, please see the line drawing
Best Seller
Drawer Track Guide and Glides, White Polyethyleneby Prime-Line Products(295)
$22
This is a white plastic track guide and glides with no back alignment tabs. The white plastic side saddles restores smooth operation of track mounted drawers.
- Constructed from white polyethylene
- Guide with no back alignment tabs
- Side saddles
- Restore smooth operation
- For further dimensional information, please see the line drawing
13/16", Right Hand Drawer Track Rollerby Prime-Line Products(557)
$18
This 13/16 in diameter roller features a 3-3/8 in. high bracket. Roller is a 5/16 in. in width. It mounts on the left side of your drawer when viewed from the rear. Contains 2 rollers and includes fasteners for a quick and easy installation.
- Used by mono-rail track drawers
- Right hand roller
- Mounting holes are 1-5/8 in. on center
- Stamped steel construction with nylon roller
- Features a 13/16 in. roller
- Mounting hardware included
- A Phillips head screwdriver is required for installation
- For further dimensional information, please see the line drawing
Best Seller
Drawer Track Back Plate, 3/8"x1", Plastic, White, 1-pairby Prime-Line Products(2793)
$22
These rear drawer track brackets are constructed of a thick, durable plastic and they come in white, left and right-hand pair. They are designed to support and maintain alignment of bottom/side-mounted steel drawer slides They feature an easy to install design, with a 3-9/16 in. socket depth to allow for front to back adjustment of the drawer slides. This pair of drawer track back plates includes the installation fasteners, and they have a maximum load rating of 75 lbs. per pair. These rear drawer replacement track sockets are simple to install and are used by many.
- Used to support side mounted drawer glides
- 3/8 in. wide x 1 in. tall x 3-9/16 in. deep openings
- Fits drawer track systems that are 3/8 in. x 1 in.
- White plastic construction
- Contains 1 pair of drawer track back plates (1 left and 1 right)
- Mounting hardware included
- A Phillips head screwdriver is required for installation
- For further dimensional information, please see the line drawing
Best Seller
Stamped Steel, Adjustable, Closet Door, Floor Guide, 2Packby Prime-Line Products(36)
$19
This is an adjustable stamped steel sliding closet door floor guide, with nylon tips. The guides are made of white nylon and can be adjusted to accommodate doors from 3/4 in. to 1-3/8 in. wide. Used by a variety of closet door manufacturers.
- Used by Acme and a variety of other closet door manufacturers
- Fits doors from 3/4 in. to 1-3/8 in. thick
- 2 guides per package
- Stamped steel base with adjustable white nylon tips
- Guides are 5/8 in. tall
- Fasteners are included
- A Phillips head screwdriver is required for installation
- For further dimensional information, please see the line drawing
White, Bottom-Mount Drawer Slides, 1-Pairby Prime-Line Products(4154)
$24
These drawer slide kits are constructed of steel tracks with plastic rollers and come in a white powder-coated finish. They feature a self-closing design that commences at the final 2-1/2 in. from the end of the 17-3/4 in. long tracks when closing. The maximum load capacity for this kit is 75 lbs., and it fits most bottom-mount drawer systems. This kit cannot be cut down to fit smaller drawer depths as it is designed with a positive stop at the ends of the fixed tracks, and because the rear rollers (11/16 in. diameter wheels) on the sliding tracks are fastened to the ends of the drawer-mounted track pieces. These bottom-mount drawer slides can be installed in drawer cabinets with face frames and without. If installing in drawer cabinet with face frame, Prime-Line part R 7240 (purchased separately) may be necessary if existing back plates are damaged. The clearance required between the drawer and the drawer opening for these types of slides is as follows: 1/2 in. on left and right sides, 1/4 in. at the bottom and 5/8 in. at the top. Installation instructions are included with each set, and they can also be found within the manufacturer�s website.
- These drawer slides can be installed in cabinetry constructed with and without face frames, that have a depth of 18 in.
- Durable steel-constructed drawer slides with plastic wheels designed for years of use
- Designed with self-closing feature that begins towards the end of the slide
- Easy to install slides fit most bottom-mount drawer systems
- Maximum load capacity is 75 lbs.
- Ideal for use in kitchen cabinets
- Installation fasteners and instructions are included
- For further dimensional information, please see the line drawing
Best Seller
Dark Brown, Drawer Track Guide and Glide, 2Packby Prime-Line Products(5016)
$18
This is a drawer guide and glide set constructed from mold injected brown plastic. Typically this set can be used with a majority of furniture drawer systems. The saddles offer less resistance on the drawer being pulled out or pushed in making this set perfect for your dressers, hutches and night stand drawers. Opening for metal track on the large piece is 15/16 in. x 3/32 in. make sure to measure your track before ordering. All the necessary mounting hardware is included for a quick and easy installation.
- Typically used for dressers, hutches and night stand drawers
- Replaces Rite-Trak Drawer Hardware
- A metal track is required for these guides but is not included
- Dark brown plastic construction
- Contains 2 dark brown plastic track case guides 2 track guides and 4 white glides
- For dressers, hutches and night stand drawers
- A Phillips head screwdriver is required for installation
- For further dimensional information, please see the line drawing
1-1/8" Classic Bronze Cam Lockby Prime-Line Products(1)
$20
This is a plated diecast housing and steel cam lock with 3 different cams, and features a classic bronze face. It can be mounted to metal or wood doors or drawers with a maximum 13/16 in. thickness. 2 Yale Y-11keys come with this cam lock. Dimensions are 1-1/8 in. length and a 3/4 in. diameter cylinder. An adjustable wrench will be required for installation.
- Used on doors and drawers that are 13/16 in. thick
- Allows you to secure drawer or cabinet
- Can be special ordered to be keyed the same
- Durable diecast and steel construction with a bronze finish
- All hardware included for installation
- Contains 1 lock, 3 cams, 1 trim collar, 1 spur washer, 2 rotation washers, 1 lock nut and 2 keys
- Body of this lock is 1-1/8 in. diameter with a face of 7/8 in. diameter
- For further dimensional information, please see the line drawing
Closet Door Guide Assembly, Bottom Mount, 2Packby Prime-Line Products(243)
$22
This closet door guide is constructed from nylon and comes affixed to an adjustable steel bracket. It features a bottom mount design that fits on Acme and other similar styled doors. This guide also acts as corner bracket for steel frame bypassing doors.
- Nylon guide with steel bracket
- Adjustable bottom mount design
- Used by several manufacturers
- Acts as a corner bracket for steel framed by-pass doors
- Provides smooth operation
- For further dimensional information, please see the line drawing
Drawer Track Guides for 1/4" by 7/8" trackby Prime-Line Products(373)
$18
These guides are constructed from brown plastic. They help in keeping your drawers aligned and make for a smoother operation. Fits a 1/4 in. by 7/8 in. track.
- Bulk pack includes guides only, the fasteners and corner saddles not included
- Fits a 1/4 in. x 7/8 in. track
- Plastic construction
- Brown colored guide
- For further dimensional information, please see the line drawing
Drawer Track Guide Kit, 1-1/8", Plastic, Green, 2Packby Prime-Line Products(16)
$19
This kit includes 2 drawer track guides that are constructed of plastic and come in a green color. These guides are used to replace damaged or missing drawer guides that have a 1-1/8 in. wide x 5/16 in. tall opening in the plastic guide. These guides are designed to fit 1-1/8 in. x 9/32 in. tracks to provide drawer alignment and smooth operation. The kit also includes white plastic saddles that are used to replace worn or missing guide buttons. These plastic saddles allow the drawers to glide easily when opening and closing, while at the same time preventing wear on the cabinet�s face frame or opening. The saddles install into the inside lower left and right corners of the drawer face opening with the fasteners provided within each kit. This kit includes enough parts to repair 2 drawers (with matching track and guide dimensions).
- Used to replace damaged or missing drawer guides that require a 1-1/8 in. x 5/16 in. guide opening
- Is 1-1/8 in. x 5/16 in
- Mounts to the back of the drawer
- Green molded plastic with white saddles
- Includes 2 guides and 4 side saddles
- Mounting hardware included
- A Phillips head screwdriver is required for Installation
- For further dimensional information, please see the line drawing
Drawer Track Delta Guide, White Plasticby Prime-Line Products(367)
$23
This drawer track delta guide is constructed from white polyethylene. It features a large bearing area for heavily loaded drawers. This type of guide has a 6-point contact that reduces lateral movement of the drawer.
- Used by a variety of drawer manufacturers
- Large bearing area for heavily loaded drawers
- 6 point contact reduces lateral movement
- White polyethylene construction
- Easy to install
- Mounting hardware included
- A Phillips head screwdriver is required for installation
- For further dimensional information, please see the line drawing
1-1/8" White, Nylon, Ball Bearing Drawer Rollers, 2Packby Prime-Line Products(261)
$20
These drawer slide roller assemblies are constructed of plastic tires and steel ball bearings. It features a 1/4" 20 mounting stud and the 1-1/8 in. outside diameter tire has a convex edge. This multi-use roller is designed for use as a replacement roller for metal drawer slide systems. Frequently used to repair damaged or missing rollers found in file cabinet drawer tracks. These rollers are easy to install and include to assemblies per package.
- Typically found on drawers and cupboard shelving units
- 1-1/8 in. diameter roller
- Features a 1/4 in. offset hub with a 1/4-20 x 3/8 in. threaded mounting stud
- White nylon roller with ball bearings
- Ball bearing feature allows for smoother operation
- Hex nut included
- Adjustable wrench required for installation
- For further dimensional information, please see the line drawing
Orange, Plastic Drawer Track Guide Kit, 2Packby Prime-Line Products(205)
$18
These guides are constructed from orange plastic. They help in keeping your drawers aligned and make for a smoother operation. Contains enough parts to repair two drawers. Fits a 9/32 in. x 1-1/8 in. track.
- Used with tracks 9/32 in. x 1-1/8 in
- Includes four side saddles for smooth operation of drawer
- Contains two support plates
- Orange plastic construction
- Easy to install
- Mounting hardware included
- A Phillips head screwdriver is required for installation
- For further dimensional information, please see the line drawing
Drawer Slides, Bottom Mount, 16" Set, Whiteby Prime-Line Products(4199)
$20
Why struggle with a drawer that won�t open or close properly when you can simply replace the slides? Whether you need to replace damaged or missing slides or are installing them new for the first time, Prime-Line part R 7210 drawer slide kit fits most bottom/side-mounted drawer systems and is for use in 16 in. deep drawer cabinets. These bottom mount drawer slides can be installed in drawer cabinets with face frames and without.
Whether you are installing new drawers or repairing one that won't open or close properly, Prime-Line drawer Slide Kit fits most bottom/side-mounted drawer systems. The drawer slide kit is constructed of steel tracks with a white powder coated finish and self-lubricating plastic rollers.
SELF-CLOSING DESIGN - The smooth-gliding tracks features a self-closing design that commences at the final 2-1/2 in. from the end of the 15-3/4 in. long tracks when closing
EASY TO INSTALL - Installation is quick and easy, and the kit contains all necessary fasteners. Installation instructions are included and also available on Prime-Line's website.
The maximum load capacity for the drawer slide kit is 75 lbs. and is for use in 16 in. deep drawer cabinets. It features a positive stop in the closed position and a double stop in the extended position that locks your drawer open, so it cannot be pulled too far out and fall off the tracks.
INSTALLATION TIP - The clearance required between the drawer and the drawer opening for these slides is: 1/2 in. on left and right sides, 1/4 in. at the bottom and 5/8 in." at the top
Whether you are installing new drawers or repairing one that won't open or close properly, Prime-Line drawer Slide Kit fits most bottom/side-mounted drawer systems. The drawer slide kit is constructed of steel tracks with a white powder coated finish and self-lubricating plastic rollers.
SELF-CLOSING DESIGN - The smooth-gliding tracks features a self-closing design that commences at the final 2-1/2 in. from the end of the 15-3/4 in. long tracks when closing
EASY TO INSTALL - Installation is quick and easy, and the kit contains all necessary fasteners. Installation instructions are included and also available on Prime-Line's website.
The maximum load capacity for the drawer slide kit is 75 lbs. and is for use in 16 in. deep drawer cabinets. It features a positive stop in the closed position and a double stop in the extended position that locks your drawer open, so it cannot be pulled too far out and fall off the tracks.
INSTALLATION TIP - The clearance required between the drawer and the drawer opening for these slides is: 1/2 in. on left and right sides, 1/4 in. at the bottom and 5/8 in." at the top
Prime Line Prod. Drawer Cam Lock U 9947by Prime-Line Products(1809)
$19
Flush mounting drawer and cabinet lock. For material thickness of 7/8". 5/16" bolt throw. Requires 7/8" diameter hole. 2 keys included. Steel brass-plated die-cast housing. Uses Y13 key blank. SKU 202444.
- No. U 9947
- Color: Brass
- Material: Steel
- Hole Diameter: 7/8"
- Maximum Door Thickness: Up to 7/8"
- Keyed: Keyed different
- Pkg Qty: 1
- Package Type: Card
Nylon L--Angle Drawer Guides, 10Packby Prime-Line Products(123)
$18
These drawer guides are constructed from plastic and mount to the front corners of your drawer opening and help keep your drawer centered. They help to reduce drawer binding and allows for smoother operation.
- Used by a variety of cabinet makers and home owners
- Allows for smoother operation
- Install 2 per drawer
- Plastic construction
- 10 Pack
- Mounting hardware included
- Will need a hammer for installation
- For further dimensional information, please see the line drawing
Pneumatic Door Closer, 10-1/2", Canada Brown, Adjustable, Medium Weightby Prime-Line Products(15)
$28
This standard duty capacity closer is used on out-swinging wood or metal doors. It also features an adjustable closing speed. Best used on medium-weight installations.
- Used on medium-weight doors
- 10-1/2 in. tube length
- Canada brown painted color
- Constructed of steel and diecast components
- Installation fasteners included
- For further dimensional information, please see the line drawing
Wood Drawer Track Repair Kit, 24", Wood/Plastic/Steel Components, 1-setby Prime-Line Products(137)
$23
This kit is constructed of a wooden track, steel brackets and a plastic guide and back plate, together with all the parts necessary to repair one wooden drawer track system. This track restores smooth operation to track mounted drawers, and it can be used for top or bottom mount installations. This universal kit allows the 24 in. wooden track to be cut down to size to accommodate for shorter drawer applications. The white plastic saddles are used to replace worn or missing guide buttons, enabling the drawers to glide easily while at the same time preventing wear on the cabinet�s face frame or drawer opening. This track system is used by many to replace missing or malfunctioning drawer track hardware.
- Used to replace damaged or missing drawer tracks and guides
- Universal hardware system fits most configurations
- 24 in. long track
- Constructed of wood, steel and plastic components
- Cut to size track
- For further dimensional information, please see the line drawing
Prime Line Prod. 13/16" Door/Drawer Lock U 9945by Prime-Line Products(6813)
SALE
$15$25
Stainless steel face; plated die-cast housing. Chrome finish. Provided with straight and offset cams. Installs in 3/4" hole. 90 deg. and 180 deg. stops. Includes 1-1/8" offset and 1-3/8" straight cams. 2 keys included. When ordering full cartons or nonkeyed alike locks, members may receive sets of 2 keyed alike. Uses Yale Y-11 keyway.
- No. U 9945
- Size: 13/16"
- Color: Chrome
- Material: Steel
- Hole Diameter: 3/4"
- Maximum Door Thickness: Up to 13/16"
- Keyed: Keyed different
- Package Quantity: 1
- Package Type: Card
Drawer and Cabinet Lock, 1-3/8", Diecast, Stainless Steel, 1" Max. Panelby Prime-Line Products(1305)
$22
This drawer and cabinet lock is constructed of diecast and steel components and it comes in a stainless steel finish. Features a 3/4 in. outside cylinder diameter with a 1-3/8 in. length that will accommodate up to 1 in. thick panels. Can be mounted to metal or wood; door and/or drawer panels, and it comes complete with 3 cams, a trim collar, 2 reversible rotation washers, 2 keys and fasteners. These are keyed alike and they uses Yale Y-11 keyway. Others have used these to replace damaged locks in work truck tool boxes and gumball machines.
- Used to secure cabinet doors and drawers up to 1 in. thick
- 3/4 in. outside diameter x 1-3/8 in. long cylinder. Fits on 1 in. maximum panel thickness
- Can be special ordered to be keyed differently
- Durable diecast and steel construction with a stainless steel finish
- All hardware included for installation
- Contains 1 lock, 3 cams, 1 trim collar, 1 spur washer, 2 rotation washers, 1 lock nut and 2 keys
- Body of this lock is 1-3/8 in. diameter with a face of 7/8 in. diameter
- For further dimensional information, please see the line drawing
3/32"x1-9/32", Yellow Drawer Guide Kitby Prime-Line Products(418)
SALE
$18$32
This drawer track guide kit is constructed from yellow plastic. These guides and glides are designed to restore the smooth operation of your track mounted drawers. They come complete with fasteners for a quick and easy installation.
- For use on rolled edge metal tracks with a 3/32 in. x 1-9/32 in
- Helps to keep drawers aligned
- Mounts to the back of the drawer
- Yellow molded plastic
- Includes 2 guides and 4 side saddles
- Mounting hardware included
- A Phillips head screwdriver is required for Installation
- For further dimensional information, please see the line drawing
Closet Door Roller, Front, 1/4" Offset, 1" Nylon Wheel, 2Packby Prime-Line Products(8)
$19
This roller is constructed from nylon and comes affixed to an adjustable bracket. It features a 1/4 in. offset top hung side mounted design. Fits on Cox and similar style doors that are 3/4 to 1-3/8 in. thick.
- Single wheel
- Pack consists of 2 rollers and 4 screws
- Used by several manufacturers
- 1 in. outside diameter Convex edged nylon wheel
- Provides smooth operation
- For further dimensional information, please see the line drawing
White, Plastic, Center Rail Drawer Track Rail Support Bracket, 2Packby Prime-Line Products(640)
SALE
$19$44
This is a drawer track center rail support bracket made of mold injected white plastic. The plate is designed so that is can be mounted either horizontally or vertically. Typically these are used with Amerock tri-roller drawer slide track and will fit most C shaped tracks. Each package contains 2 center rail drawer tack brackets and all the necessary mounting hardware to make a quick and easy installation.
- Used with most Amerock tri-roller drawer slide tracks
- Can be mounted horizontally or vertically
- Accepts most C shaped tracks
- White plastic construction
- Affixes to the back of the cabinet
- All necessary mounting hardware is included for a quick and easy installation
- A Phillips head screwdriver is required for installation
- For further dimensional information, please see the line drawing
Drawer Side Track Back Bracketsby Prime-Line Products(101)
SALE
$18$21
These Rear Drawer Track Sockets by Prime-Line Products are constructed from durable plastic and come white in color. It fits on most side mounted drawer track systems. This style of drawer track support brackets accept most ball bearing drawer slides. They feature 5/16 in. wide x 7/8 in. tall x 3 in. deep openings and 2-7/8 in. socket depth, which allows for front to back adjustment of the drawer slides. Installation is quick and easy, and all fasteners are included. The maximum load rating is 75 lbs. per pair.
- All components constructed of a thick and durable plastic, for sure support
- Comes in a solid white color to match white painted, metal drawer slide hardware
- Designed for use with most side mounted drawer track systems and accepts most all ball bearing drawer slide hardware
- Features deep socket depths to allow for easy front to rear adjustments
- Easy to install with only a few simple tools
- For further dimensional and specification information, please see the line drawing
- A Phillips head screwdriver is required for installation
Drawer Track Back Plate, 5/16"x7/8", Plastic, White, 1-pairby Prime-Line Products(263)
SALE
$19$32
These rear drawer track brackets are constructed of a thick, durable plastic and they come in white, left and right-hand pair. They are designed to support and maintain alignment of bottom/side-mounted steel drawer slides (like Prime-Line parts R-7210 through R-7214). They feature an easy to install design, with a 2-7/8 in. socket depth to allow for front to back adjustment of the drawer slides. This pair of drawer track back plates includes the installation fasteners, and they have a maximum load rating of 75 lbs. per pair. These rear drawer replacement track sockets are simple to install and are used by many.
- Typically used on side mounted, steel ball bearing drawer guides
- Mounted on the cabinet behind the drawer
- Depth of sockets allows for small adjustment from front to back on rail
- Made of durable white plastic
- Can also be used for bottom mount drawer slides
- Mounting hardware included
- A Phillips head screwdriver is required for installation
- For further dimensional information, please see the line drawing
13/16", Left Hand Drawer Track Roller, 2Packby Prime-Line Products(953)
SALE
$18$22
This 13/16 in. diameter roller features a 3-1/2 in. high bracket. Roller is a 5/16 in. in width. It mounts on the left side of your drawer when viewed from the rear. Contains 2 rollers and includes fasteners for a quick and easy installation.
- Used by mono-rail track drawers
- Left hand roller
- Features 3/16 In. roller
- Stamped steel construction with nylon roller
- 2 Pack
- All the necessary mounting hardware is included for a quick and easy installation
- A Phillips head screwdriver is required for installation
- For further dimensional information, please see the line drawing
Shelf Support Pegs, 1/4", Steel Construction, Brass, 50Packby Prime-Line Products(6)
SALE
$22$26
These shelf support pegs are constructed from steel and come plated in a brass plated finish. They are designed to fit into 1/4 in. diameter holes, for use in cabinets and bookshelves. These pegs feature a 20 lb. maximum safe load capacity (per peg) and can be used for many applications. These shelf support pegs are easy to install and are used by many manufacturers.
- Used to support adjustable shelving
- 1/4 in. outside peg diameter, with 1/2 in. x 11/16 in. seat
- Brass plated finish
- Steel construction
- Easy to install
- For further dimensional information, please see the line drawing
Bottom Mount RV and Mobile Home Drawer Slides, White, 1-setby Prime-Line Products(32)
$23
This is a set of one pair of 21-3/4 in. white metal drawer slides for use in 22 in. deep drawer cabinets. They have a maximum safe load capacity of 75 lbs.
- Mating Frame and Drawer Steel Brackets
- Self Lubricating Rollers
- White powder coated finish
- Steel tracks with flat plastic wheels
- 1 Set includes hardware for one complete drawer
- For further dimensional information, please see the line drawing
Drawer Track Center Roller, 13/16", Left Hand, 2Packby Prime-Line Products(34)
$18
This 13/16 in. diameter roller features a 3-1/2 in. high bracket. It mounts on the left side of your drawer when viewed from the rear. Contains 2 rollers and includes fasteners for a quick and easy installation.
- Mono-rail roller for drawer slide systems
- Left hand design
- Plastic roller
- Used on drawers
- Provides smooth operation
- For further dimensional information, please see the line drawing
Rim Cylinder Lock, 3/4in. Hole Center, Diecast, Brass Plated, Kwiksetby Prime-Line Products(210)
SALE
$21$33
This Rim Cylinder Lock by Prime-Line Products is constructed from heavy-duty zinc diecast materials and steel components, whose face comes in a corrosion-resistant, and brass-plated finish. This rim cylinder lock includes a beautifully finished trim ring, a strong and durable mounting plate, installation screws and 2 brass keys. Another great feature of this lock is that it can be re-keyed to fit a different key cut, and it can be used to replace Kwikset, Weiser or Weslock locks.
- Constructed of diecast, steel and brass components
- Comes in a corrosion resistant, brass plated finish to match existing hardware
- Designed for use with a variety of deadlocks and deadbolt security hardware
- Features two keys, trim ring, mounting plate and installation fasteners
- Easy to install with only a few simple tools
- For further dimensional and specification information, please see the line drawing
Drawer Track Guides and Glides, 4Packby Prime-Line Products(1)
$18
This drawer track guide and glides are constructed from plastic. It features a rear mounted design that keeps this item out of sight. It is used for aligning drawers and helps for a smooth operation.
- Includes guides and side saddles
- Fits a 1/4 in. x 1-1/16 in. track
- Plastic construction
- White colored guide
- White colored saddles
- For further dimensional information, please see the line drawing
5/8-in Brass Die-Cast Drawer and Cabinet Lockby Prime-Line Products(1239)
SALE
$19$22
This swing bar door guard will increase peace of mind when answering the door by allowing the door to be cracked open slightly for viewing. When engaged, a ball on the keeper interlocks with the bar lock and prevents an intruder from pushing their way through. Although a standard swing bar door guard can add great security to your home, condo, apartment/flat, or hotel room, there has been some concern over the wide availability of emergency release tools, which are meant to release swing bar door guards in cases of emergency. We have improved upon the standard door guard design and added an innovative backup thumb turn security lock that blocks the release tool from disengaging the door guard latch. In cases of emergency, hotel security or emergency crews can pop the thumb turn off of the unit by applying approximately 100 pounds of force to the door. Note that 100 lbs. Of force is much greater than a simple kick in, so the emergency release feature does not compromise your security. Additionally, after the thumb turn lock breaks away, the unit still operates as a traditional swing bar door lock and a specially designed Anti-Lockout emergency access tool is required to swing the door guard out of place. To help prevent forced entry into your home, it is always a good idea to engage the backup thumb turn lock whenever you are not actively using your door. Defender Security by Prime-Line offers a full line of security hardware designed to protect your home and loved ones. All are keyed the same.
- Used on doors and drawers that are 5/16 in. thick
- Allows you to secure drawer or cabinet
- Can be special ordered to be keyed the same
- Durable diecast and steel construction with a bright brass finish
- Contains 1 lock, 3 cams, 1 trim collar, 1 spur washer, 2 rotation washers, 1 lock nut and 2 keys
- Body of this lock is 5/8 in. diameter with a face of 7/8 in. diameter
- For further dimensional information, please see the line drawing